Research on Industrial Shape Meter and its Application

Abstract:

A industrial strip shaper is developed, which mainly consisted of the shape detecting roller, the collecting ring, the DSP shape signal processing board and the shape control model. The structural form which is different from the international popular segmented detection roller is put forward and the entire detection roller inlayed block is developed to avoid the scratch of the strip surface due to different thermal expansion of the traditional detection roller measuring unit effectively. The signal transmission form which is different form the international popular dry slip ring is put forward, the spray wet slip ring is developed to improve the measuring precision and the service life. The signal processing form which is different form the international popular gathering card is put forward and the embedded DSP shape signal processing hardware system is developed to improve the measuring precision and the anti-interference ability. The shape signal processing software system whose function contains error compensation, pattern recognition, establishment of the target shape and the close loop control calculation is built to implement the intelligentized shape meter. The shape meter has been test chronically on the 1250 mm cold strip mill of Angang Steel Company Limited and the test result indicates that the measuring signals were stable and reliable and the close loop control of shape was implemented.

• Periodical: Advanced Materials Research (Volumes 311-313)
• Pages: 898-901
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.311-313.898
• Online since: August 2011
• Authors: Bing Qiang Yu, Li Po Yang
• Keywords: Cold Rolling Strip, Shape Control, Shape Detecting, Shape Meter

References

[1] Lejiang Xu. shape control and mill type selection of cold mill strip[M]. Beijing: Metallurgical Industry Press, 2007. (In Chinese)

[2] Junsheng Wang, Jinlan Bai, Xianghua Liu. Theory and process control of cold strip rolling [M]. Beijing: Science Press, 2009. (In Chinese)

[3] Lihong Yang, Fei Yan, Zhaohui Ma. Research and development of pre-coated steel for automotive industry [J]. Iron and Steel, 2009, 44(12):1-7. (In Chinese)

[4] Bo Zhai, Rongsheng Sun, Jianlin Sun. Application of sheet shape control technology on continuous rolling mills in Angang [J]. Aisc Techniques, 2009, 355(1):49-52.

[5] Guodong Hu, Qi Wang, Benyou Zou. Differential output shape meter of mageto-elastic transformer for cold rolling strip [J]. Iron and Steel, 1994, 29(4): 56-59. (In Chinese)

[6] Shimin Xu, Bingqiang Yu, Guodong Hu. Shape meter of pressing magnetic type for cold rolling strip to applicating 4-roller reversible rolling mill [J]. Metallurgical Equipment, 2004, 10: 39-40. (In Chinese)

[7] Qilin Zhao, Junsheng Wang, Guodong Wang. Development and application of a measured flatness value processing method [J]. Journal of Materials and Metallurgy, 2009, 8(4): 294-296.

[8] Junsheng Wang, Zhengyi Jiang. A flying gauge change model in tandem cold strip mill [J]. Journal of Materials Processing Technology, 2008, 204: 152-161.

DOI: 10.1016/j.jmatprotec.2007.11.046

[9] Jian Liu, Yiqun Wang, Xiaojun Hu, et al. Dynamic calibration of pneumatic strip shape measuring rolls and phase correction compensation method of system circumferential error [J]. Steel Rolling, 2009, 26(1): 26-29. (In Chinese)

[10] Xuguang Sun, Yiqun Wang, Guofang Yin. Main technical performance of pneumatic strip shape measuring roll. Journal of Iron and Steel Research, 2006, 18(12): 47- 49.

[11] Yabo Sun, Hongmin Liu, Yan Peng. Influence of variation of the on_line shape of cold rolled strip on shape measuring and controlling system and its compensating measures [C]. Proceedings of Second International Conference on Modeling and Simulation, 2009, 6: 212-219.

DOI: 10.1109/icie.2009.98

[12] Bingqiang Yu, Hongmin Liu, Lipo Yang, etc.. A new type of contact shape meter and its industry application [C]. International Conference on Measuring Technology and Mechatronics Automation (ICMTMA2009), 2009, 4: 1058 -1061.

DOI: 10.1109/icmtma.2009.49

[13] Zhiming Li, Yan Peng, Bingqiang Yu, etc.. A shape measurement system for cold-rolled steel strip based on DSP [C]. 2009 WASE International Conference on Information Engineering, 2009, 2: 257- 260.

DOI: 10.1109/icie.2009.98

[14] Hongmin Liu, Lipo Yang, Bingqiang Yu, et al. entire-inlayed-block-intelligence-type shape meter [P]. Chinese Patent: CN101694368A, 2010-4-7. (In Chinese)

[15] Bingqiang Yu, Lipo Yang, Hongmin Liu, etc.. Development and industry application of contact shape meter with new structure [J]. Chinese Journal of Scientific Instrument, 2010, 31(4): 904-911. (In Chinese)