Characterization of Al-7Si-Mg-Cu Turbine Impeller Produced by Investment Casting

Abstract:

Application of a light-weight material, such as an aluminum alloy, on a turbine impeller can enhance the efficiency of an Organic Rankine Cycle power plant that operates at temperatures below 150 °C. The density of an aluminum alloy only one-third that of steel. However, increased strength of aluminum alloys is needed for turbine impeller qualification. Investment casting was chosen to produce radial inflow turbine impeller due to their complex geometry and precision. It can replace machining process, which is time-consuming and less efficient because of material removal. This study describes the investment casting process used to produce a radial inflow impeller turbine. The study also identifies defects, microstructures and properties of radial inflow turbine impeller. The turbine impeller were produced from Al-7Si-4Mg alloy with 0.38, 3.82, and 6.0 wt. % Cu. Visual examination showed that the turbine impeller was free of macro defects and misruns. Microstructures were characterized by Optical Microscopy and SEM. The structures consisted of α-Al, Si eutectic, AlMgSi, AlMgFeSi (Chinese script) and CuAl₂. The higher hardness value of 54HRB was affected by Cu content due to the good mechanical properties of fasa CuAl₂^.

• Periodical: Advanced Materials Research (Volume 789)
• Pages: 324-329
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.789.324
• Online since: September 2013
• Authors: Muhammad Syahid, Bondan Tiara Sofyan, Singgih G. Basuki, Bayu Adam
• Keywords: Aluminium Alloy, Investment Casting, Organic Rankine Cycle (ORC), Turbine Impeller

References

[1] Yamamoto, T., Furuhata, T., Arai, N., Mori, K., Design and testing of the Organic Rankine Cycle, Journal of Energy, Vol. 26, 2001, p.239–251.

DOI: 10.1016/s0360-5442(00)00063-3

[2] Kang, S. H., Design and experimental study of ORC (organic Rankine cycle) and radial turbine using R245fa working fluid, Energy, Vol. 41, 2012, pp.1-11.

DOI: 10.1016/j.energy.2012.02.035

[3] Kusumawardani, J, Response ageing of Al-2Cu-9Si with the addition of Al-Ti grain refining powder 0. 027 wt. % Titanium, Final Project Univ. Indonesia, (2008).

[4] Jones, S. and Yuan, C., Advances in shell moulding for investment casting, J. Mat. Proc. Tech., Vol. 135, 2003, p.258–265.

[5] Jovanovic, M. T, Dimcic, B., Bobic, I., Zec, S., Maksimovic, V., Microstructure and mechanical properties of precision cast TiAl turbocharger, J. Mat. Proc. Tech., Vol. 167, 2005, pp.14-21.

[6] Lia, D. Z., Campbell, J., Li, Y. Y., Filling system for investment cast Ni-base turbine blades, J. Mat. Proc. Tech., Vol. 148, 2004, p.310–316.

DOI: 10.1016/j.jmatprotec.2004.02.032

[7] Gunasegaram, D. R., Farnsworth, D. J., Nguyen, T. T., Identification of critical factors affecting shrinkage porosity in permanent mold casting using numerical simulations based on design of experiments, J. Mat. Proc. Tech., Vol. 209, pp.1209-1219.

DOI: 10.1016/j.jmatprotec.2008.03.044

[8] Kliauga, A. M., Vieira, E. A., Ferrante, M., The influence of impurity level and tin addition on the ageing heat treatment of the 356 class alloy, J. Mat. Sci. & Eng. Vol A 480, 2008, p.5–16.

DOI: 10.1016/j.msea.2007.07.091