Research on Compressive Behavior and Deformation Heating of 7075-T6 Aluminum Alloy during Hot Compression

Dong Ge Wang; Rui Bin Mei; Ban Cai; Chun Li Zhang; Li Bao; Bo Zhang; Chang Sheng Li

doi:10.4028/www.scientific.net/AMR.887-888.315

Paper Titles

Brief Introduction of Microwave Ceramics Developed in our Labs for Dielectric Resonators
p.294

The Effects of K/Na Ratio on the Electrical Properties of (Li, Sb, Ta) Modified KNN Piezoelectric Ceramics at Reduced Temperature with KNbO₃ as Sintering Aid
p.299

Structure and Performance of Calcined Bauxite
p.305

Microstructure and Compression Deformation Behavior in the Quasicrystal-Reinforced Mg-6Zn-2Y Alloy Solidified under Super-High Pressure at Room-Temperature
p.311

Research on Compressive Behavior and Deformation Heating of 7075-T6 Aluminum Alloy during Hot Compression
p.315

Aircraft Bearings Fracture Failure Analysis
p.319

An Experimental Investigation on the Solubility of Zr in Cu-Sn Alloys
p.324

Grain Structure and Precipitates in Squeeze Casting Al-Li-Mg-Zr Alloy
p.329

Dynamics of Phase Transformation in Cu-Cr-Zr Alloy
p.333

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 887-888Research on Compressive Behavior and Deformation...

Research on Compressive Behavior and Deformation Heating of 7075-T6 Aluminum Alloy during Hot Compression

Abstract:

The flow stress behavior of the 7075-T6 aluminum alloy was studied through single-pass compression experiment by using MMS-300 simulator within temperature range of 300-450°C and strain rate range of 0.01-40s^-1. Then a simulation of compression was carried out and the influence of deformation velocity on load and deformation heating was investigated according to the relationship between stress and strain. The results show that dynamic recrystallization occurs in hot compression of 7075-T6 alloy and the stress-strain curves are presented as wave. Furthermore, the flow stress curves have the same wave period and the fluctuation range increases with an increase of strain rate and a decrease of strain. Increasing of deformation velocity results in higher critical strain but the value decreases when the deformation velocity is much higher. The temperature rise increases with the increase of deformation velocity and decrease of deformation temperature. The maximum of temperature rise is more than about 30°C, so that the deformation heating is significant.

You might also be interested in these eBooks

Advances in Materials and Materials Processing IV

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 887-888)

Pages:

315-318

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.887-888.315

Citation:

Cite this paper

Online since:

February 2014

Authors:

Dong Ge Wang, Rui Bin Mei, Ban Cai, Chun Li Zhang, Li Bao, Bo Zhang, Chang Sheng Li

Keywords:

7075-T6 Alloy, Critical Strain, Deformation Heating, Hot Compression

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] Y.G. Wang and Z. X Jiang: Mater. Sci. Eng., A. Vol. 553 (2012), pp.176-180.

Google Scholar

[2] S. L Dai, K. Zhang and S.J. Yang: Advanced Aeronautical Aluminum Alloy Materials Technology and Application (National Defense Industry Press. China 2012).

Google Scholar

[3] G.Y. Lin, H. Zhang and W.C. Guo: Chin. J. Nonferrous Metal Vol. 11 (2001), pp.412-415.

Google Scholar

[4] G.Z. Quan, Y.P. Mao and G.S. Li: Comput. Mater. Sci., Vol. 55 (2012), p.65–72.

Google Scholar

[5] K.W. Liu, K.Y. Hu and F.H. Cao: Hot Working Technology Vol. 41 (2012), pp.19-21.

Google Scholar

[6] Y. Wang, Z.C. Sun and Z.Y. Li: Chin. J. Nonferrous Metal Vol. 21(2011), pp.2880-2887.

Google Scholar

[7] Y.F. Wu, S.H. Li and B. Hou: Chin. J. Nonferrous Metal Vol. 23(2013): 658-665.

Google Scholar

[8] E. Cerri, E. Evangelista and A. Forcellese: Mater. Sci. Eng., A. Vol. 197(1995), pp.181-198.

Google Scholar

[9] Z.J. Luo, Q. Yang and W.H. Ji: Chin. J. Nonferrous Metal Vol. 10 (2000), pp.804-808.

Google Scholar