Rheological Investigation of MIM Feedstocks for Reducing Frictional Effects during Injection Moulding

Abstract:

An experimental investigation of the rheological properties for abrasive Metal Injection Moulding feedstocks is presented for different materials with dissimilar particle sizes and shapes. Tribological issues are inevitable since feedstock has up to 93 wt. % powder loading in the feedstock. In this study, each of the relatively soft carbonyl iron powder and the hard, abrasive Iron oxide powder are mixed with binder system, consisting of HDPE (High-density polyethylene), Paraffin Wax and S.A. (Stearic Acid) at different magnitudes of volumetric powder loading. The rheological properties such as flow rate (cm³/s), shear rate (s^-1) and viscosity (Pa.s) are investigated for varying conditions of temperature and pressure. The properties of the feedstocks made from the two materials showed significant variation in flow behaviour (due to difference in inter-particle frictional behaviour) with changing process parameters as well as material parameters. Furthermore, to study flow behaviour of feedstocks apparent viscosity is plotted against temperature and shear rate in order to establish the sensitivity of temperature and pressure. Flow behaviour index was determined by analysing variation of viscosity with shear rate of feedstock. As expected, results show that the feedstock having iron oxide powder with hard irregular shaped particles exhibits a higher viscosity if compared to the spherical particles in the Carbonyl iron powder feedstock. It was observed that the feedstock containing iron oxide powder (75 wt. % powder loading) gives higher shear rate but the feedstock dissociates faster with increasing temperature, whereas carbonyl iron powder feedstocks (90 wt. % powder loading) were found to be more stable (dissociate less) at higher temperatures and flowed at a smaller shear rate. Additions of graphite powder to the hard and abrasive iron oxide powder (to facilitate reduction of the iron oxide during sintering) would also be expected to improve the flow behaviour of the iron oxide feedstock on account of the superior lubricating properties of the graphite powder.

• Periodical: Advanced Materials Research (Volumes 966-967)
• Pages: 196-205
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.966-967.196
• Online since: June 2014
• Authors: Kedarnath K. Rane*, Prashant P. Date
• Keywords: Activation Energy, Frictional Effects, MIM, Rheology

References

[1] Li Yimin, H. Baiyun, Qu Xuanhui, Improvement of rheological and shape retention properties of wax based MIM binder by multi-polymer components, Trans. Nonferrous Met. Soc. China, Vol. 9, No. 1, 1999, pp.22-29.

[2] R. M. German and K. F. Hens, S. P. Lin, Key Issues in Powder Injection Molding, Ceramic Bulletin, Vol. 70, No. 8, 1991, pp.1294-1302.

[3] M. Omar, The influence of stearic acid on the properties of injection moulding of stainless steel powder, Journal of Technology, Vol. 10, No. 2, 2001, pp.37-45.

[4] P. Bhave, Metal Injection Moulding Standards Review, The international journal of powder metallurgy, Volume 27. No. 1, 1991, pp.277-281.

[5] R. M. German, A. Bose, Injection moulding of Metal and Ceramic, Metal Powder Industries Federation, Princeton, N. J, (1997).

[6] C. Karatas, A. Kocer, H. Unal, S. Saritas, Rheological properties of feedstocks prepared with steatite powder and polyethylene-based thermoplastic binders, Journal of Materials Processing Technology, Vol. 152, 2004, pp.77-83.

DOI: 10.1016/j.jmatprotec.2004.03.009

[7] M. Khakbiz, A. Simchi, R. Bagheri, Analysis of the rheological behavior and stability of 316L stainless steel- TiC powder injection molding feedstock, Materials Science and Engineering A, Vol. 407, 2005, pp.105-113.

DOI: 10.1016/j.msea.2005.06.057

[8] M. H. I. Ibrahim, N. Muhamad, A. B. Sulong, Rheological Characterization of Water Atomised Stainless Steel SS316L for Micro MIM, Advanced Materials Research Vols. 264-265, 2011, pp.129-134.

DOI: 10.4028/www.scientific.net/amr.264-265.129

[9] K. K. Rane, P. P. Date, Pulverisation of forging scale and grinding sludge: A new technique for recycling of metallic scrap from forging industries, IconSWM-2014, p.08.

[10] M. Amin, K. R. Jamaludin, N. Muhamad, Rheological properties of SS316L MIM feedstock prepared with different particle sizes and powder loadings, Journal. The Institution of Engineers, Malaysia, Vol. 71, No. 2, 2009, pp.59-62.