If-Then Rules for Selection the Die-Set for Sheet Metal Punching and Blanking Dies

Abstract:

Die-set is an essential tool accessory in sheet metal punching and blanking. The selection of the die-set represents an important activity in the die design operation. Time and money consumed in this operation could be saved by using an automated selection system for die-set components. This paper discusses an intelligent die-set selection system using the AutoCAD platform. The developed system is able to work as either standalone or connected with any die design CAD system by using the well-known AutoCAD programming tools. The proposed system is built using IF-THEN rules approach. The system code is developed using AutoCAD with Visual Basic. A data-base of Nasr Automotive Company (NASCO) for die-set was considered, from which suitable size of die-set was selected automatically. The proposed system could reduce the consumed time in the tool room department from hours to minutes and could reduce effort and cost as well.

• Periodical: Advanced Materials Research (Volume 980)
• Pages: 208-213
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.980.208
• Online since: June 2014
• Authors: H.M.A. Hussein*, J. Abu Qudeiri, U. Umer, R.K. Abdel-Magied
• Keywords: Blanking Die, Computer Aided Selection, Die-Set, If-Then Rules, Punching Die, VBA

References

[1] J.A.W. Hijink, A.C.H. van der wolf, On the Design of Die-Sets, Ann CIRP. 24 (1975) 357-360.

[2] U.P. Singh, P.C. Veenstra, J. A. H. Remaekers, J.A.W. Hijink, Numerical analysis of four column under-drive press equipped with 4 guide pillar sub press, Sheet Metal Industries. (1976).

[3] U.P. Singh, P.P. Miller, CAD of die-set, Proceeding of the 2nd Conference NMC. (1985).

[4] U.P. Singh, H.J.J. Kals, A.H. Streppel, Computer aided design of a die-set for punching/blanking, Proceedings of 28th International MTDR Conference. (1990) 379-386.

DOI: 10.1007/978-1-349-10890-9_52

[5] U.P. Singh, H.J.J. Kals, A.H. Streppel, Design study of a punching/blanking tool geometry, Proceedings of IMC Conference. (1990) 806-820.

[6] S. Kumar, R. Singh, An intelligent system for selection of die-set of metal stamping press tool, Journal of Materials Processing Technology, 164-165 (2005) 1395-1401.

DOI: 10.1016/j.jmatprotec.2005.02.066

[7] S. Kumar, R. Singh, An intelligent system for selection of die gages of progressive die, 2nd National Conference on Intelligent Systems & Networks (ISN-2005).

[8] S. Kiani, P.R. Vallance, A.H. Slocum, Errors in progressive dies for electronic components, ASPE annual meeting, Monterey, CA. (1999).

[9] R.R. Vallance, S. Kiani, A predictive model for variation in the pitch between stamped pilot holes, Transactions of the ASME, Journal of Manufacturing Science and Engineering. 125 (2003) 384-393.

DOI: 10.1115/1.1559158

[10] B.V. S Rao, G.C.M. Reddy, G.K.M. Rao, P. Ranadheer, P.V. R Reddy, Low cost knowledge base system for design of deep drawing die set, International Journal of Mechanical Engineering and Robotics Research. 2 (2013).

[11] M.G. Shebl, M.I. Ghobrial, N.F. Hassan, H.M.A. Hussein, Computer aided design and drafting of sheet metal blanking dies, Jupiter'99, Ain Shams Univeristy, Scientific Bulletin. 34 (1999) 611-624.

[12] H.M.A. Hussein, L.A. Abdeltif, M.I. Etman, A.F. Barakat, An approach to construct an intelligent system in sheet metal cutting die design, 9th Cairo university international conference on mechanical design & production (MDP-9) Cairo, Egypt, (2008).