Paper Titles

Strain Hardening Anisotropy of Aluminium Alloys during Complex Loading: Strain Reversal Effects
p.521

Numerical Study of the Influence of Imperfection of the Tip of a Vickers Indenter on Ultramicrohardness Test Results
p.525

Forming Limit Diagram for 6016-T4 Aluminium Alloy Deformed along Linear and Complex Strain Paths
p.529

Numerical Modelling of Carbon/Epoxy Laminated Plate Impact Damage
p.533

A New Anisotropic Yield Criterion for Aluminium Alloys
p.537

Reverse Deep Drawing: Experimental and Numerical Simulation Results
p.541

In-House Development and Application of Solidification Simulation Software
p.545

Comparison of Experimental and Simulated Results for a Mild Steel and a Dual-Phase Steel Deformed under Tension and Deep-Drawing
p.549

Transparent and Antiglare Conducting Coatings Deposited by Wet Chemical Processes
p.555

HomeKey Engineering MaterialsKey Engineering Materials Vols. 230-232A New Anisotropic Yield Criterion for Aluminium...

A New Anisotropic Yield Criterion for Aluminium Alloys

Article Preview

Abstract:

You might also be interested in these eBooks

Advanced Materials Forum I

Info:

Periodical:

Key Engineering Materials (Volumes 230-232)

Pages:

537-540

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.230-232.537

Citation:

Cite this paper

Online since:

October 2002

Authors:

Oana Cazacu, Frédéric Barlat

Keywords:

Anisotropic Yielding, Generalized Invariants, Polycrystalline Materials

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2002 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

[1] D.C. Drucker: J. Appl. Mech. Vol. 16 (1949), p.349.

[2] J. W. F Bishop and R. Hill: Phil. Mag. Vol. 42 (1951), p.414.

[3] R. Hill: Proc. Roy. Soc. Lond A. Vol. 193 (1948), p.281.

[4] F. Barlat, Y. Maeda, K. Chung, M., Yanagawa, J.C. Brem, Y. Hayashida, D. J. Lege, K. Matsui, S. J. Murtha, S. Hattori, R. C. Becker,. and S. Makosey: J. Mech. Phys. Solids. Vol. 45 (1997), p.1727.

DOI: 10.1016/s0022-5096(97)00034-3

[5] W. F. Hosford: J. Appl. Mech. Trans. ASME, Vol. 39 (1972), p.607.

[6] O. Cazacu and F. Barlat: Submitted for publication to Int. J. Engng. Sci (2000).

[7] F. Barlat, J. W. Yoon, R. E. Dick, F. Pourboghrat, S. H. Choi, J. C. Brem, K. Chung, D. J. Lege, and E. Chu: Submitted for publication to Int. J. Mechanical Sciences (2000). Angle from rolling direction (degrees) 0 10 20 30 40 50 60 70 80 90 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 Experiment Hill [3] Present Theory r value