Study on Advanced Cutting Tools Fabricated from Coated Powders and Their Cutting Performance

C. Z. Huang et al., "Study on Advanced Cutting Tools Fabricated from Coated Powders and Their Cutting Performance", Key Engineering Materials, Vols. 259-260, pp. 19-25, 2004

Online since:

March 2004

Authors:

Chuan Zhen Huang, B. Fang, Zhan Qiang Liu, Han Lian Liu, Sui Lian Wang, Xing Ai

Keywords:

Ceramic Tool Material, Coated Powder, Coating Ceramic Tool, Sol-Gel Method, Tool Wear

Export:

RIS, BibTeX

Price:

$41.00

Permissions:

Request Permissions

Add to Cart

References

[1] S.G. Xiao: Advanced Tool Materials (Chongqing University Press, P.R. China 1992). (in Chinese).

[2] K. Karapantev: Proc. 3rd European Meeting on Chemical Vapour Deposition (Switzerland, 1980).

[3] C.Z. Huang, J. Wang and X. Ai: International Journal of Machine Tools & Manufacture Vol. 40(6) (2000), p.823.

[4] C.J. Brinker: Sol-gel ScienceThe Physics and Chemistry of Sol-gel Processing (Academic Press Inc., Britain 1990).

[5] F.J. Zhang: Material Science and Technology Vol. 4(1) (1996), p.10 (in Chinese).

[6] K.G.G. Warrier: J. Mater. Science Vol. 29 (1994), p.3415.

[7] X. Ai, and H. Xiao: Cutting with Ceramic Tools (Mechanical Industry Press, P.R. China 1988). (in Chinese).

[8] F. Mikio, F. Kenji and F. Akira: Wear Vol. 102 (1985), p.195.

Paper TitlePages

Development of ZrO₂/ ZTA / TiC Composites

Authors: Eniko Volceanov, Ştefania Motoc, Adrian Volceanov, Rodica M. Neagu, Cristian Coman

2283

New Ceramic Products from Slate and Aluminium Sludge Wastes

Authors: Isabel M. Martins, Claudino Xavier, Maria Helena Mendonça, Manuela Oliveira

Abstract: Previous studies had shown that a promising material could be obtained by mixing aluminium-rich sludge with slate powder (with Al2O3:SiO2 molar proportion of 2:1), shaping by uniaxial pressing and sintering at 1300oC, in order both to detoxify the sludge by fixing the metals in a leach-resistant ceramic matrix and to yield a new material from the reactions of the above compounds at high temperature. In view of potential applications, since this material was also found to be inert after leaching tests, a further systematic study, reported in the present paper, was carried out, in order to determine its mechanical properties and discuss them in function of the microstructure. The average values of Vickers hardness HV3 (683), bend strength (126 MPa), Young's modulus (161GPa) and fracture toughness (3.35 MPa.m1/2) are significantly higher than those found for the as sintered slate powders, which is attributed to the increased fraction of α- alumina and reduced content of glassy phase in the microstructure of the material with sludge addition.

1695

Synthesis Processes of Nano Alumina Abrasive

Authors: Zi Cheng Li, Zhi Hong Li, Ai Ju Zhang, Yu Mei Zhu

Abstract: Synthesis processes of nano alumina abrasive precursor using precipitation method and sol-gel method were investigated in this study. Using pressureless sintering, the nano alumina abrasive was prepared. Mechanical properties of the samples were measured by using single particle compressive strength tester. The microstructures of them were examined by using field emission scanning electron microscopy (FESEM). The results indicated that the performance and microstructure of the samples are greatly relative to the synthesis processes. Compared with samples prepared by precipitation method, the samples prepared by sol-gel method have higher compressive strength, smaller grain size and more uniform microstructure. The average grain size of the alumina abrasive was below 100nm.

691

Diffusion Study of Alumina Gray Cast Iron Pair

Authors: Karolina Pereira Santos Tonello, Vânia Trombini Hernandes, Ana Helena A. Bressiani, José Carlos Bressiani

Abstract: Specific properties of structural ceramics such as their mechanical and thermal stability permit their use in high-speed cutting processes that involve deep cuts and low wear rates. The process by which wear occurs in tribological contacts is complex and cannot be explained by one simple wear mechanism. The contribution of different mechanisms to the total wear of a component is related to the mechanical and chemical properties of both the materials and the contact interface. In this investigation, diffusion tests were carried out to determine the influence of chemical interactions between alumina composite and gray cast iron, without the interference of mechanical wear mechanisms. These tests were carried out at 1100°C using static couples. The tests did not generate a strong metal–ceramic interface, indicating that the alumina composites were chemically stable under the test conditions.

739

Influence of Zirconia Content and Grain Size on Physical and Mechanical Properties of Zirconia Toughened Alumina Ceramics

Authors: Bao Yu Du, Bo Zhao, Tie Lin Duan

Abstract: Physical and mechanical properties as well as microstructure of zirconia toughened alumina ceramics with different zirconia content were tested. The results show that the best physical and mechanical properties are obtained in sub-micron composite ceramic when zirconia content is 25%; while the physical and mechanical properties of nano-zirconia toughened alumina ceramics are far better than those of sub-micron zirconia toughened alumina ceramics. Therefore physical and mechanical properties of ceramics can be improved significantly by adding proper amount of zirconia into alumina matrix and refining zirconia particles.

485