Energy Management Systems for Energy Harvesting in Structural Health Monitoring Applications

Abstract:

Autonomous structural health monitoring systems with independent power sources and wireless sensor nodes are increasingly seen as the best solution for monitoring a diverse range of machines and structures including pumps, bridges and aircraft. Powering these systems using harvested energy from ambient sources provides an attractive alternative to the use of batteries which may be either inaccessible for routine maintenance or unsuitable (for example in aerospace applications). A number of techniques are currently being considered including harvesting energy from vibration and thermal gradients. Harvesting energy can however lead to a highly variable power supply in opposition to the requirements of a wireless sensor node which requires continuous standby power with an additional capacity for power peaks during transmission of data. A power management system with embedded energy storage is therefore necessary in order to match supply and demand. Due to the low levels of power harvested in a number of applications, an important factor in the design of such a system is its efficiency to ensure sufficient power reaches the sensor node. Based on the requirements for a simple power management system for thermoelectric power harvesting consisting of a rectifier, a DC/DC convertors and a battery, this paper first examines the possibilities in terms of basic components with a number of commercially available units tested and characterised. Potential designs for a management system incorporating these components are then discussed and a blueprint for an optimal system is suggested.

• Periodical: Key Engineering Materials (Volume 518)
• Pages: 137-153
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.518.137
• Online since: July 2012
• Authors: M. Arnold, C.A. Featherston, Matthew R. Pearson, J. Lees, Aleksander Kural
• Keywords: Energy Harvesting, Power Management, Thermoelectric

References

[1] C.A. Featherston, K.M. Holford, G Waring, Thermoelectric Energy Harvesting For Wireless Sensor Systems in Aircraft, Key Engineering Materials, 413-414 (2009), 487-494.

DOI: 10.4028/www.scientific.net/kem.413-414.487

[2] A. Harb, Energy harvesting: State-of-the-art, Renewable Energy, 36 (2011), 2641–2654.

DOI: 10.1016/j.renene.2010.06.014

[3] C. Donovan, A. Dewan, H. Peng, D. Heo D, H. Beyenal, Power management system for a 2. 5 W remote sensor powered by a sediment microbial fuel cell, Journal of Power Sources, 196 (2011) 1171–1177.

DOI: 10.1016/j.jpowsour.2010.08.099

[4] M. Marzencki, Y. Ammar, S. Basrour, Integrated power harvesting system including MEMS generator and a power management circuit, Sensors and Actuators A, 145 (2008) 363–370.

DOI: 10.1016/j.sna.2007.10.073

[5] P. Li, Y. Wen, P. Liu, X. Li, C. Jia, A magnetoelectric energy harvester and management circuit for wireless sensor network, Sensors and Actuators A, 157 (2010) 100–106.

DOI: 10.1016/j.sna.2009.11.007

[6] A. Anders, Temperature as Energy Source, Powering Wireless Sensor Networks, Munich 2011, accessed 14/06/(2011).

[7] R. Percival, Energy Storage for Wireless Sensor Networks - Introduction and Case Study, Powering Wireless Sensor Networks, Munich 2011, accessed 14/06/(2011).

[8] R. Svehla, In-Flight and Simulated Aircraft Fuel Temperature Measurements, accessed 26/04/2011, http: /ntrs. nasa. gov/archive/nasa/casi. ntrs. nasa. gov/ 19910006105 1991006105. pdf. Tem-URL.

[9] D.M. Rowe, G. Min, Evaluation of thermoelectric modules for power generation, Journal of Power Sources, 73 (1998)193–198.

DOI: 10.1016/s0378-7753(97)02801-2

[10] Micropelt simulation tool mypelt,. Accessed 08/06/2011, URL http: /www. micropelt. com/products/mypelt. php.

[11] K. Ozawa, Lithium Ion Rechargeable Batteries, Weinheim: Wiley-VCH, 1st edition, (2009).