Fabrication & Microstructure of TiB2+TiC Duplex Particulates Reinforced Carbon Steel Matrix Surface Composite

Chang Qing Guo

doi:10.4028/www.scientific.net/KEM.575-576.198

Paper Titles

Preparation and Microstructure of Nano ZrB₂ Reinforced Aluminum Matrix Composites
p.179

Numerical Analysis on the Cure-Induced Deformation of Fiber Composite Laminates
p.183

Numerical Analysis on the Influence of Interface on the Mechanical Behavior of Unidirectional Fiber Composites under Different Loads
p.188

Interfacial Effect on Bending Property of Al/Cu/Al Laminated Composite Produced by Asymmetrical Roll Bonding
p.194

Fabrication & Microstructure of TiB₂+TiC Duplex Particulates Reinforced Carbon Steel Matrix Surface Composite
p.198

Comparison of Mechanical and Frictional Properties of PTFE Matrix Composites Reinforced by Different Fibers and Graphite
p.203

Facile Synthesis of Hierarchical Architecture FePO₄/C Composite Microspheres
p.209

Fabrication of Bifunctional SiO₂/Europium-Polyoxometalates/Ag Particles and their Luminescence and Catalysis Properties
p.216

Synthesis and Characterization of g-C₃N₄/α-Fe₂O₃ Composites with Enhanced Photocatalytic Activity
p.225

HomeKey Engineering MaterialsKey Engineering Materials Vols. 575-576Fabrication & Microstructure of TiB2+TiC Duplex...

Fabrication & Microstructure of TiB₂+TiC Duplex Particulates Reinforced Carbon Steel Matrix Surface Composite

Abstract:

This paper presents a novel fabrication process that combines SHS with V-EPC (vacuum expandable pattern casting) and microstructural features of TiB₂+TiC duplex particulates reinforced surface composite with carbon steel matrix. Macro structural observation shows that the surface composite is dense and there are no obvious defects. Microstructural investigation demonstrates that the composite from surface to core is consisted of three different layers, i.e., the top surface compound layer, the interim transitional layer and the bottom carbon steel matrix. A large amount of fine TiB₂and TiC duplex particles are evenly distributed in the composite matrix, while the concentration are significantly decreased and non-uniform distribution increased for these particles in the interim layer.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volumes 575-576)

Pages:

198-202

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.575-576.198

Citation:

Cite this paper

Online since:

September 2013

Authors:

Chang Qing Guo

Keywords:

Composite, SHS, TiB₂+TiC Particles, V-EPC

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] B. Yu, Y. C. Lou．Fabrication and Microstructures of In-situ Synthesized TiB2 Particulates Reinforced Fe Matrix Composite . Foundry (in Chinese). 2003, 52（6）：387-389.

Google Scholar

[2] W. Y. Yan, B. K. Wei, Z, Y, Fu. In-Suit Synthesized TiCp/Fe Composites at atmosphere in Fe-Ti-C melt . Composites (in Chinese). 2000, （3）：51-59.

Google Scholar

[3] S. Xiandong, L. Chengping, L. Zhuoxuan and O. Liuzhang. The Fabrication and Properties of Particle Reinforced Cast Metal Matrix Composites. J. Mat. Proc. Tech, 1997, 63: 426.

DOI: 10.1016/s0924-0136(96)02659-3

Google Scholar

[4] R. J. Li. Ceramic-Metal Composites. Beijing：Metallurgical Industry Press, 2004, 3-5.

Google Scholar

[5] J. H. Yi, T. M. Ye, Y. D. Peng. Research Progress and Prospect of the Process in Warm Compaction in Powder Metallurgy. Powder Metallurgy Technology (in Chinese). 2005, 23（2）：140-144.

Google Scholar

[6] W. H. Han. Study on TiB2 Particle Reinforced Carbon Steel Matrix Surface Composite. Baotou, Inner Mongolia University of Science & Technology, (2011).

Google Scholar

[7] Z. Q. Zhang. Fe-Ti-B4C system fabricated TiC-TiB2 particles reinforced Cr bearing steel matrices selected area composites. Jilin, Jilin University, (2006).

Google Scholar