New Ways at the Fine Grinding

Abstract:

The traditional approach to grinding is to operate within the limits of surface quality. The requirements for surface quality in grinding are higher than those in other common machining operations such as turning and milling. The surface quality of machined parts is very important for precise production and assembly. When we focus on roughness parameters after grinding, we can establish the limits of these parameters for typical grain materials: Al₂O₃, SiC, CBN, SG and others. Increasing demands on accuracy and quality of production leads to research concerned with the properties of these materials and the surface quality after grinding. This paper shows new possibilities for the ground surface with focus on surface roughness obtained under varying combinations of cutting conditions. The influence of the grinding wheel, cutting parameters and coolant on higher surface quality is assessed by roughness parameters Ra, Rz, Rt and the Material portion of a surface profile. These high-precision ground surfaces are shown to have a Nanometres (10^-9) unit topography demonstrating that the process is able to replace other finishing technologies such as superfinishing or honing.

• Periodical: Key Engineering Materials (Volume 581)
• Pages: 255-260
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.581.255
• Online since: October 2013
• Authors: Martin Novák
• Keywords: Grinding, High Precision, Roughness, Surface

References

[1] Holesovsky, F., Novak, M. 2010. Influence of grinding on machine parts with desing notches, Manufacturing Technology IX, UJEP, Usti n. Labem, 40-46 pp.

[2] Kocman, K. 2010. Analyza vyvojovych brousicich kotoucu na bazi mikrokrystalickeho korundu, Strojirenska technologie, vol. XV, no. 3, UJEP, Usti nad Labem, 40-47 pp.

[3] Michna, S., Naprstkova, N. 2012. Research into the causes cracking of aluminum alloys of Al – Cu during mechanical machining, Manufacturing Technology, vol. 12, no. 12, 47-51 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/1/47

[4] Müller, M., Valasek, P. 2012. Abrasive wear effect on Polyethylene, Polyamide 6 and polymeric particle composites, Manufacturing Technology, vol. 12, no. 12, 55-59 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/1/55

[5] Neslusan, M., Rozsipal, M., Kolarik, K., Ochodek V. 2012. Application of Barkhausen Noise for Analysis of Surface Integrity after Hard Turning, Manufacturing Technology, vol. 12, no. 12, 60-65 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/1/60

[6] Vasilko, K., Macurova, A. 2012. Two local extremes of cutting speed, Manufacturing Technology, vol. 12, no. 12, 86-89 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/1/86

[7] Madl, J. 2012. Surface Properties in Precise and Hard Machining, Manufacturing Technology, vol. 12, no. 13, 158-166 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/2/158

[8] Novak-Marcincin, J. Torok, J. Barna, J., Novakova-Marcincinova, L. 2012. Technology of Perspective Scanning Methods for Realization of 3D Models of Manufacturing Devices, Manufacturing Technology, vol. 12, no. 13, 186-191 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/2/186

[9] Kundrak, J., Varga, G., Deszpoth, I., Molnar, V. 2013. Some aspects of the hard machining of bore holes, Applied Mechanics and Materials 309, pp.126-132.

DOI: 10.4028/www.scientific.net/amm.309.126

[10] Kundrak, J., Gyani, K., Bana, V. 2008. Roughness of ground and hard-turned surfaces on the basis of 3D parameters International Journal of Advanced Manufacturing Technology, Vol. 38, Iss. 1-2, pp.110-119.

DOI: 10.1007/s00170-007-1086-9

[11] Vasilko, K., Macurova, A. 2012. Two Locals Extremes of Cutting Speed. Manufacturing Technology, vol. 12, no. 12, 86-89 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/1/86

[12] Novak, M., Naprstkova, N., Ruzicka. L. 2012. New ways in aluminium alloys grinding. In Key Engineering Materials, vol. 496: Precision Machining IV. TTP, Zurich, 132 – 137 pp. WOS: 000302674400023.

DOI: 10.4028/www.scientific.net/kem.496.132

[13] Kusmierczak, S., Naprstkova, N., Svobodova, J. 2012. 2012. Evaluation of sheet degradation with surface treatment, Engineering for Rural Development, vol. 11, 32-36 pp.

[14] Varga, G., Kundrák, J. 2013. Effect of environmentally conscious machining on machined surface quality, Applied Mechanics and Materials 309, pp.35-42.

DOI: 10.4028/www.scientific.net/amm.309.35

[15] Marinescu, I., D., et all. 2007. Handbook of Machining with Grinding wheels, Boca Raton: CRC Press, 592 pp.

[16] Michna, S., Naprstkova, N. 2012. The use of fractography in the analysis of cracking after formed workpiece blank mechanical machining from the AlCuSnBi alloy, Manufacturing Technology, vol. 12, no. 13, 174-178 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/2/174

[17] Lukovics, I., Bilek, O., Holemy, S. 2010. Development of Grinding Wheels for Tools Manufacturing, Manufacturing Technology, vol. X., no. 10, UJEP, Usti nad Labem, 10-16 pp.

DOI: 10.21062/ujep/x.2010/a/1213-2489/mt/10/1/10

[18] Sládek, A., Fabian, P., Pastirčák, R., Brezničan, M. 2012. The Roundness and Microstructure of Thin-wall Bearing Rings, Manufacturing Technology, vol. 12, no. 13, 237-241 pp.

DOI: 10.21062/ujep/x.2012/a/1213-2489/mt/12/2/237

[19] Malkin, S. 1989. Grinding Technology: Theory and applications of machining with abrasives, SME, 275pp.

[20] Novak, M. 2011. Surface quality of hardened steels after grinding. Manufacturing Technology, vol. XI, no. 11, UJEP, Usti nad Labem, 55-59 pp.

DOI: 10.21062/ujep/x.2011/a/1213-2489/mt/11/1/55

[21] Holesovsky, F., Novak, M. 2010. Grinding and its influence to ground surface durability. Proceedings of International Conference on Advances in Materials and Processing Technologies, Paris. Publisher: Amer INST Physics, Melville, NY, USA. ISBN 978-0-7354-0871-5. WOS: 000287169300158.

[22] Novak, M. 2012. Influence of the Corrosion Surrounding on Surface Quality of Ground Hardened Steels In Key Engineering Materials, vol. 496: Precision Machining IV. TTP, Zurich, 25 – 30 pp., WOS: 000302674400005.

DOI: 10.4028/www.scientific.net/kem.496.25