Feasibility Study of Waste Motor Recycling through Manual Dismantling and Hydrometallurgical Process

Abstract:

Huge amount of waste electrical and electronic equipments (WEEE) or electronic waste (E-waste) has been produced every year in the world. It consists of valuable and hazardous metals that can be reused or extracted to minimize the environmental impact. This study is focusing on the investigation of recycling potential of e-waste through manual dismantling process and leaching test. The leaching test was conducted by changing the initial pH with constant stirring speed, constant water-sample ratio and in open air. The morphological structures of the solid samples were observed by SEM and the liquid residue was analyzed by Atomic Absorption Spectroscopy (AAS). It was found that total time required to dismantle all parts in the waste motor is about 10 minutes and the part that required longest dismantling time was armature windings. The metal elements that were observed are Fe, Mg, Pb and Cr. It was found that the pH of the solution increased with the increasing leaching time. The dissolution of Fe and Pb was high in the early stage of leaching but gradually decreased afterward. The dissolution for Mg and Cr was low throughout the leaching process. It was revealed that the metal elements in e-waste can be dissolved using this method and further investigation to increase the dissolution rate is required to ensure that the method proposed is applicable in industry. However, dissolved concentration of Pb must be controlled to ensure that it follows the permissible amount set under environmental standard.

• Periodical: Key Engineering Materials (Volumes 594-595)
• Pages: 990-995
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.594-595.990
• Online since: December 2013
• Authors: Nik Hisyamudin Muhd Nor, Thirumoorthy Nathan, Shafizan Jaibee, Mohd Hafiz Burhan, Fariza Mohamad, Al Emran Ismail, Sia Chee Kiong, Zulkifli Ahmad, Yokoyama Seiji
• Keywords: Dissolution, E-Waste, Hydrometallurgical, Leaching, Recycling, Waste Motor

References

[1] Information on Department of Environment Malaysia, E-waste inventory project in Malaysia, http: /www. env. go. jp/en/recycle/asian_net/Project_N_Research/E-wasteProject/06. pdf.

[2] T.L. Chong: E-waste Management, Impak 1 (2008) pp.12-13.

[3] A. Terazono et. Al, Current status and research on E-waste issues in Asia, J Mater Cycles Waste Management 8 (2006) pp.1-12.

[4] X. Huo, L. Peng, X.J. Xu, L.K. Zheng, B. Qiu, Z.L. Qi, et al.: Elevated blood lead levels of children in Guiyu, an electronic waste recycling town in China. Environ Health Perspect 115 (2007) pp.1113-1117.

DOI: 10.1289/ehp.9697

[5] N.N. Ha, T. Agusa, K. Ramu, N.P.C. Tu, S. Murata, et al.: Contamination by trace elements at e-waste recycling sites in Bangalore, India. Chemosphere 76 (2009) pp.9-15.

DOI: 10.1016/j.chemosphere.2009.02.056

[6] H. Li, L. Yu, G. Sheng, J. Fu and P. Peng: Severe PCDD/F and PBDD/F pollution in air around an electronic waste dismantling area in China, Environ. Sci. Technol. 41 (2007) pp.5641-5646.

DOI: 10.1021/es0702925

[7] T. Oishi, K. Koyama, S. Alam, M. Tanaka and J. C. Lee: Recovery of high purity copper cathode from printed circuit boards using ammoniacal sulphate or chloride solutions, Hydrometallurgy 89(1-2) (2007) pp.82-88.

DOI: 10.1016/j.hydromet.2007.05.010

[8] Y. J. Park and D. Fray: Recovery of high purity precious metals from printed circuit boards, Journal of Hazardous Materials 164(2-3) (2009) pp.1152-1158.

DOI: 10.1016/j.jhazmat.2008.09.043

[9] M.N. N Hisyamudin, S Yokoyama, M Kawakami and M Umemoto: Reaction Between CO2 and CaO Under Wet Grinding, Powder Technology 196(2) (2009) pp.156-162.

DOI: 10.1016/j.powtec.2009.07.014

[10] S. Yokoyama, A. Suzuki, M.N.N. Hisyamudin, H. Kanematsu, A. Ogawa, T. Takahashi, M. Izaki and M. Umemoto: Serial Batch Elution of Electric Arc Furnace Oxidizing Slag Discharged from Normal Steelmaking Process into Fresh Water, ISIJ International 50(4) (2010).

DOI: 10.2355/isijinternational.50.630

[11] S. Yokoyama, A. Suzuki, M.N.N. Hisyamudin, H. Kanematsu, A. Ogawa, T. Takahashi, M. Izaki and M. Umemoto: Serial batch elution of electric arc furnace oxidizing slag discharged from normal steelmaking process into fresh water, Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan 96(12) (2010).

DOI: 10.2355/tetsutohagane.96.698

[12] Z. Zainudin: Benchmarking River Water Quality in Malaysia, Jurutera February (2010) pp.12-15.

[13] B. H. Robinson: E-waste: An assessment of global production and environmental impacts, Science of the Total Environment 408 (2009) pp.183-191.

DOI: 10.1016/j.scitotenv.2009.09.044

[14] A.K. Ahmad, I. Mushrifah and M.S. Othman: Water Quality and Heavy Metal Concentrations in Sediment of Sungai Kelantan, Kelantan, Malaysia: A Baseline Study, Sains Malaysiana 38(4) (2009) pp.435-442.