Paper Titles
Flexural Properties of Polyamides: Influence of Strain Rate, Friction and Moulding-Induced Anisotropy
p.29
Measurement of Thermoplastics Tensile Proprieties Using Digital Image Correlation
p.33
Evaluation of the Thermally Sprayed Cermet Coatings Adhesion by Scratch Test
p.37
Deflection Determination of V-Beam Thermal Sensors Using Digital Image Correlation
p.41
State of Stress Determination in a Water Drinker by Numerical and Experimental Methods
p.45
Mechanical Behaviour of Nickel Based Amorphous Alloys during Tensile Test at Different Strain Rates
p.50
Measurement and Analysis of Noise Generated in a Tram Rail Wheel Contact
p.54
A Comparison of Composite Bars against Metallic Bars from the Mass per Unit Length Point of View
p.58
Effect of Exploitation Conditions and Flaw Geometry on the Load Carrying Capacity of Casing Pipes for Oil Drilling Rigs
p.65

State of Stress Determination in a Water Drinker by Numerical and Experimental Methods

Article Preview

Abstract:

This paper presents the evaluation of residual stresses and stresses induced by external loads in a water drinker by numerical and experimental methods. The part, used in animal husbandry, is made of grey cast iron (EN GJL 200). Numerical simulations were based on the finite element method, using ANSYS Workbench software to determine the stresses produced by external loads and finite volume method, using NovaFlow software, to determine residual stresses. The results obtained by numerical methods, were validated by experimental methods. Applied experimental methods consist of electrical resistive strain gauge technique to determine the state of stress in various loading conditions and the blind hole method to determine residual stresses, respectively.

You might also be interested in these eBooks
Proceedings of the 14th Symposium on Experimental Stress Analysis and Materials Testing View Preview

Info:

Periodical:

Key Engineering Materials (Volume 601)

Pages:

45-49

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.601.45

Citation:

Cite this paper

Online since:

March 2014

Authors:

Ioan Aurel Cherecheș, Cristian Dudescu, Gheorghe Daniel Lakatos, Ioan Vidican, Mircea Bejan

Keywords:

Blind Hole Method, Control Volume Method, Finite Element Method (FEM), Residual Stress, Strain Gauge Technique

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2014 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] Cherecheș, I., A., Bejan, M., Industrial maintenance – applicability in the zootechnical sector. Risk prevention in maintenance activities (in romanian). Publishing house MEGA, Cluj-Napoca, 2011, ISBN 978-606-543-174-4, pag. 227-236.

Google Scholar

[2] Păstrav, I., Bejan, M., Bal, N., Szocs, L., Current status and prospects of residual stresses determination by non-destructive methods. First part. The XI technical and scientific communication session (in romanian), Aiud, (1988).

Google Scholar

[3] Bal, N., Residual stresses in machine parts, PhD thesis (in romanian), Technical University of Cluj-Napoca, (1998).

Google Scholar

[4] NovaFolw&Solid CV version 4. 3 r5, www. novacastfoundry. se.

Google Scholar

[5] Cherecheș, I., A., Bejan, M. Determination of casting residual stresses, Acta Technica Napocensis, vol. 55, IssueI, 2012, Technical University of Cluj-Napoca, pag. 141-146.

Google Scholar

[6] S1265 - Strain gages and accessories, www. hbm. com.

Google Scholar

[7] AIAS - Asociazzione italiana per l`analisi delle solecitazzioni, The hole-drilling strain gauge method for the measurement of uniform or non-uniform residual stresses, Florence, (2010).

Google Scholar