Influences of Inhibitor and Firing Temperature on Efflorescence Reduction of Clay Products

Abstract:

For ceramic industry, efflorescence is undesirable and cannot be completely eliminated from the finished products. The efflorescence is caused by soluble salts in the raw material and mostly appears as white deposit at the product’s surface. In this research, the removal of sulfate in the raw materials was studied. In addition, the sulfate ions were immobilized by forming a water-insoluble compound. The sulfate ions in the raw materials and fired products were extracted by distilled water, and the concentration was determined by using a UV-visible spectroscopy following the ASTM C1580-09 standard. Three sources of the raw materials from Tambon Suan Phung, Ratchaburi, Tambon Mae Win and Mae Ta, Chiang Mai, were analyzed for sulfate concentrations. The clay from Tambon Suan Phung, Ratchaburi which had the highest sulfate concentration was selected for further study on the effect of inhibitor and firing temperature on efflorescence inhibition. To reduce solubility of the sulfate, three kinds of inhibitor, i.e. barium chloride, barium carbonate and barium hydroxide, were added into the raw material at various concentrations, i.e. 0.5, 1.0, 1.5 and 2.0 wt% and homogeneously mixed by ball milling followed by the addition of distilled water to prepare the clay slip. The clay products were mold casted to 1 x 1 x 3 inch³ in size. Then, they were fired at 800, 900 and 1000 °C. It has been revealed that the addition of barium carbonate at 2 wt%, which is the highest amount employed in this study, and firing temperature of 900 °C resulted in least sulfate leaching due to the formation of water-insoluble barium sulfate. To perform a field test, the fired samples with and without the addition of barium carbonate were immersed in water for 4 months. The efflorescence was observed on the sample without barium carbonate within the 1^st month. In contrast, with the addition of barium carbonate, no efflorescence was observed after testing for 4 months.

• Periodical: Key Engineering Materials (Volume 659)
• Pages: 111-115
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.659.111
• Online since: August 2015
• Authors: Sunisa Jindasuwan*, Pim Chakornnipit, Sitthisuntorn Supothina
• Keywords: Barium Carbonate, Clay Products, Efflorescence, Firing Temperature

References

[1] A. Andrés, M.C. Díaz, A. Coz, M.J. Abellán, J.R. Viguri, Physico-chemical charcterisation of bricks all through the manufacture process in relation to efflorescence salts, J. Eur. Cer. Soc. 29 (2009) 1869-1877.

DOI: 10.1016/j.jeurceramsoc.2008.11.015

[2] H. Brocken, T.G. Nijland, White efflorescence on brick masonry and concreate masonry blocks, with special emphasis on sulfate efflorescence on concreate blocks, Constr. Build. Mater. 18 (2004) 315-323.

DOI: 10.1016/j.conbuildmat.2004.02.004

[3] L. Hennetier, J.V. Almeida, A.M.S. Correia, V.M. Ferreira, Efflorescence and its quantification in ceramic building materials, Brit. Cer. Trans. 100(2) (2001) 72-76.

DOI: 10.1179/096797801681233

[4] W.E. Brownell, Fundamental factors influencing efflorescence of clay product, J. Am. Cer. Soc. 32(12) (1949) 375-389.

DOI: 10.1111/j.1151-2916.1949.tb18917.x

[5] D.R. Aron, Salts efflorescence on brick, Tonind. Ztg. 1(19) (1877) 147.

[6] M. Dondi, B. Fabbri, G. Guarini, M. Marsigli, C. Mingazzini, Soluble salts and efflorescence in structural clay products: A scheme to predict the risk of efflorescence, Bo. Soc. Esp. Ceram. Vidrio. 36(6) (1997) 619-629.

[7] W.E. Brownell, Efflorescence resulting from sulfates in clay raw materials, J. Am. Cer. Soc. 41(8) (1958) 310-314.

DOI: 10.1111/j.1151-2916.1958.tb12922.x

[8] W.E. Brownell, Application of new techniques to the solution of an efflorescence problem, J. Am. Cer. Soc. 33(12) (1950) 360-363.

[9] ASTM C1580-09 Standard test method for water-soluble sulfate in soil.

[10] ASTM C67-02c Standard test method for sampling and testing brick and structural clay tile.