Effects of Water Temperatures on Water-Soluble Binder Removal in Ceramic Materials Fabricated by Powder Injection Moulding

Abstract:

This work focuses on the debinding conditions of the ceramic materials fabricated by powder injection moulding. Ceramic powder materials, including alumina and alumina-based composites were prepared as feedstocks and mixed with water-soluble polyethylene glycol (PEG) and polyvinyl butyral (PVB). The PEG/PVB binder mixture, with PEG to PVB ratio of 85:15 by weight and powder loading of 44 vol%, were thoroughly mixed and injected into the mould at the temperature of 190 °C to obtain rod-like specimens. Prior to sintering, the as-injected specimen was then leached in water, the temperature of which was varying from 30 (ambient temperature), 45 to 60 °C, in order to get rid of PEG and leave the specimens in shape by PVB. The rate of PEG removal according to different water temperatures was investigated. The experimental results suggested that PEG could completely be eliminated by 45 and 60 °C water without any dimensional disintegration in 5 hours whereas those leached in 30 °C water showed only 70% PEG removal. Higher water temperatures led to fast PEG removal rate at the beginning and then gradually decreased with elapsed times.

• Periodical: Key Engineering Materials (Volume 659)
• Pages: 90-95
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.659.90
• Online since: August 2015
• Authors: Wantanee Buggakupta*, Nutthita Chuankrerkkul, Juthathep Surawattana
• Keywords: Polyethylene Glycol, Powder Injection Moulding, Water-Soluble Binder

References

[1] G. Thavanayagam, K. Pickering, J.E. Swan and P. Cao, Analysis of rheological behavior of titanium feedstocks formulated with a water-soluble binder system for powder injection moulding. Powder Metallurgy 269(2015) 227-232.

DOI: 10.1016/j.powtec.2014.09.020

[2] J. Hidalgo, C. Abajo, A. Jiménez-Morales and J.M. Torralba, Effect of a binder system on the low-pressure powder injection moulding of water-soluble zircon feedstocks. Journal of European Ceramic Society (33)15–16 (2013) 3185–3194.

DOI: 10.1016/j.jeurceramsoc.2013.06.027

[3] N. Chuankrerkkul, P. Chakartnarodom, Fabrication of injection moulded 304L stainless steel reinforced with tungsten carbide particles. Materials Science Forum 706-709 (2012) 638-642.

DOI: 10.4028/www.scientific.net/msf.706-709.638

[4] Z. Xie, L. Wang, X. Yang and Z. Zhang, Water debinding for zirconia powder injection moulding. Key Engineering Materials 368-372 (2008) 732-735.

DOI: 10.4028/www.scientific.net/kem.368-372.732

[5] N. Chomsirigul, O. Khuanthong, P. Sooksaen and N. Chuankrerkkul, Influence of specimen dimensions and temperature on the debinding behavior of alumina feedstock. Key Engineering Materials 608 (2014) 170-174.

DOI: 10.4028/www.scientific.net/kem.608.170

[6] M. Sood, R. Munigeti, K.S. alexander and A.T. Riga, Effects of polyethylene glycol molecular weight on its DSC melting and crystallization properties.

[7] J. Surawattana, Powder injection moulding of alumina and alumina/tungsten carbide composites. Master Degree Thesis, Ceramic Technology, Department of Materials Science (2011) Faculty of Science, Chulalongkorn University.

[8] L. Wang, J.L. Shi, J.H. Gao, D.S. Yan, The influence of addition of WC particles on mechanical properties of alumina matrix composites. Materials Letter 50 (2011) 179-182.

DOI: 10.1016/s0167-577x(01)00221-x

[9] N. Chuankrerkkul, W. Buggakupta and J. Surawattana, Role of tungsten carbide reinforcement on alumina matrix composite fabricated by powder injection moulding. Key Engineering Materials 608 (2014) 230-234.

DOI: 10.4028/www.scientific.net/kem.608.230