Strength and Stiffness Calculation of Small Diameter Gun Drills

Abstract:

The results of strength and stiffness calculations of gun drills with steel and cemented carbide stems are presented. Four cross-sections of gun drills are examined and recommendation for selection of proper shape in terms of strength and stiffness is given. Finite element modeling of gun drills shown that the highest stress concentration is at the bottom of the V-shaped flute in the middle of the length of the stem. Gun drill testing under production conditions confirmed the results of finite element modeling.

• Periodical: Key Engineering Materials (Volume 685)
• Pages: 340-344
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.685.340
• Online since: February 2016
• Authors: Artem Babaev*, B.A. Tukhfatullin, A.B. Kim
• Keywords: Destruction, Gun Drill, Stiffness, Strength, Strength of Materials, Torsion

References

[1] Kirsanov S.V., Grechishnikov V.А., Grigoryev S.N., Skhirtladze А.G. Treatment of deep holes in mechanical engineering: handbook, М.: Mechanical engineering, (2010).

[2] Eichler R. Prozesssicherheit beim Einlippenbohren mit kleinsten Durchmessern. Diss. Stuttgart.: Institut für Werkzeugmaschinen, (1996).

[3] Tsarenko М. А. The experience in designing single-lip drill for accurate and deep holes Ø2, 22…3, 30 mm. Aviation technology, the device - and aggregate building. 4 (1984) 59-63.

[4] Streicher P. Tiefbohren der Metalle. Verfahrenstechnische und Konsrtruktive Probleme. Würzburg: Vogel-Verlag, (1975).

[5] Kirsanov S.V., Babaev A.S., Small-diameter hard-alloy bits for gun production. Russian Engineering Research, 33 (2013) 170-171.

DOI: 10.3103/s1068798x13030088

[6] Leckie F.A., Dal Bello D.J. Strength and Stiffness of Engineering Systems. Springer Science+Business Media. LLC (2009).

[7] Tuhfatullin B.А., Maksak V.I. The program for calculating the geometric characteristics of the cross section formed by several circuits. # 2013619136, (2013).

[8] Karpilovskiy V.S. SCAD Office. The formation of cross-sections and calculation of geometrical characteristics. М.: АСВ, (2004).

[9] Biermann D., Wolf M., Aßmuth R. Cutting edge preparation to enhance the performance of single lip deep hole drills. Procedia CIRP. 1 (2012) 172-177.

DOI: 10.1016/j.procir.2012.04.030

[10] Sihvo I., Varis J. The wear of single flute gun drill and tool life tests. Mechanika. 5 (2008) 59-64.

[11] Heisel U., Eichler R. Werkzeugverhalten und –optimierung beim Einlippenbohre. Spanende Fertigung. Essen : Vulkan-Verl., (1994) 86-102.

[12] Silva V.D. Mechanics and Strength of Materials. Springer-Verlag, Berlin Heidelberg. (2006).

[13] Goncharov P.S. et. al. NX Advanced Simulation. Engineering analysis. М.: DMK Press. (2012).

[14] Kirsanov S. V., Babaev A. S. The study of deep holes accuracy and surface roughness after gun drilling. Proceedings of 2014 International Conference on Mechanical Engineering, Automation and Control Systems, MEACS 2014, IEEE. (2014) 109804.

DOI: 10.1109/meacs.2014.6986950

[15] Astakhov V.P. Gundrilling Know-how. Cutting Tool Engineering Magazine. 53, 12 (2001).