Investigation of Side-Dam Plate in Single-Wheel Caster for Casting Rods

Toshio Haga; Taisei Miyake

doi:10.4028/www.scientific.net/KEM.805.31

Paper Titles

Weldability of Similar and Different Metallic Materials
p.8

Computer Simulation and Analysis of the Parameters of the Drawing Process of Thin Wire from the Alloy Pd-5Ni
p.13

Study of the Influence of Conditions of Combined Casting and Rolling-Extruding and Two-Stage Annealing on the Structure and Properties of Semi-Finished Electrical Products from an Al–Zr System Alloy
p.19

Computer Modeling and Analysis of the Energy-Power Process Parameters of the Combined Machining of Alloys Al-Mg System
p.25

Investigation of Side-Dam Plate in Single-Wheel Caster for Casting Rods
p.31

Forming of Small Projection on Roll-Cast A356 Strip by Cold Rolling and Small Groove on PET Plate Using A356 Die
p.37

600 mm-Wide Strip Casting Using Single Roll Caster Equipped with Scraper
p.43

Effect of Latent Heat of Aluminum Alloys on Bonding between Strips in Clad Strip Cast by a Twin-Roll Caster
p.50

Mechanical Properties of PP/clay Nanocomposites Prepared from Masterbatch: Effect of Nanoclay Loadings and Re-Processing
p.59

HomeKey Engineering MaterialsKey Engineering Materials Vol. 805Investigation of Side-Dam Plate in Single-Wheel...

Investigation of Side-Dam Plate in Single-Wheel Caster for Casting Rods

Abstract:

The cross section of a thin rod cast by a single-wheel caster, for which the wheel cross section is an inverted trapezoidal groove, is concave. To make the cross section convex, an inner side-dam plate is proposed. A single-wheel caster with a flat wheel (without a groove) and rotating side-dam plates is also proposed. 5182 aluminum alloy rods with a convex or rectangular cross section can be cast. The area of the rod is smaller than 150 mm². The diameter of the converted circle area is 15 mm.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 805)

Pages:

31-36

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.805.31

Citation:

Cite this paper

Online since:

June 2019

Authors:

Toshio Haga*, Taisei Miyake

Keywords:

Inside Side Dam Plate, Rod, Rotating Side Dam Plate, Single Wheel Caster

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] T. Haga, Effect of the contacting condition between molten metal and roll on Al-12%Si alloy strip cast by melt drag method, Japan Inst. Light Met. 48 (1998) 613-617.

DOI: 10.2464/jilm.48.613

Google Scholar

[2] R. E. Maringer, Solidification on a substrate, Mater. Sci. Eng. 98 (1988) 13-20.

Google Scholar

[3] T. A. Gaspar, T. J. Bruce, L. E. Hackman, S. E. Brasmer and J. A. Dantzig, Rapidly solidified titanium alloys by melt overflow, NASA-CR-4253, 198.

Google Scholar

[4] T. Haga, H. Watari, S. Kumai, High speed twin roll casting of Mg alloy strip by a vertical type twin roll caster, Arch. Mater. Sci. Eng. 15 (2006) 186-192.

DOI: 10.1299/jsmeintmp.2005.2_5

Google Scholar

[5] T. Haga, M. Ikawa, H. Watari, S. Kumai, High speed twin roll casting of Al-3Si-0. 6Mg strip, Arch. Mater. Sci. Eng. 17 (2006) 337-340.

Google Scholar

[6] T. Haga, M. Ikawa, H. Watari, S. Kumai, High speed twin roll casting of 6016 strip, Arch. Mater. Sci. Eng. 18 (2006) 371-374.

Google Scholar

[7] T. Haga, H. Inui, H. Watari, S. Kumai, Casting of aluminum alloy strip using an unequal diameter twin roll caster, Arch. Mater. Sci. Eng. 29 (2008) 113-116.

DOI: 10.1016/j.jmatprotec.2007.03.012

Google Scholar