Forming of Small Projection on Roll-Cast A356 Strip by Cold Rolling and Small Groove on PET Plate Using A356 Die

Toshio Haga; Yhuta Nakazawa

doi:10.4028/www.scientific.net/KEM.805.37

Paper Titles

Computer Simulation and Analysis of the Parameters of the Drawing Process of Thin Wire from the Alloy Pd-5Ni
p.13

Study of the Influence of Conditions of Combined Casting and Rolling-Extruding and Two-Stage Annealing on the Structure and Properties of Semi-Finished Electrical Products from an Al–Zr System Alloy
p.19

Computer Modeling and Analysis of the Energy-Power Process Parameters of the Combined Machining of Alloys Al-Mg System
p.25

Investigation of Side-Dam Plate in Single-Wheel Caster for Casting Rods
p.31

Forming of Small Projection on Roll-Cast A356 Strip by Cold Rolling and Small Groove on PET Plate Using A356 Die
p.37

600 mm-Wide Strip Casting Using Single Roll Caster Equipped with Scraper
p.43

Effect of Latent Heat of Aluminum Alloys on Bonding between Strips in Clad Strip Cast by a Twin-Roll Caster
p.50

Mechanical Properties of PP/clay Nanocomposites Prepared from Masterbatch: Effect of Nanoclay Loadings and Re-Processing
p.59

Influence of Sintering Temperature on Physical and Mechanical Properties of Hydroxyapatite-Calcium Titanate Composite
p.65

HomeKey Engineering MaterialsKey Engineering Materials Vol. 805Forming of Small Projection on Roll-Cast A356...

Forming of Small Projection on Roll-Cast A356 Strip by Cold Rolling and Small Groove on PET Plate Using A356 Die

Abstract:

A small projection with a height and width of about 40 and 50 µm, respectively, was formed on a twin-roll-cast A356 aluminum alloy sheet by cold rolling at a rolling speed of 0.5 m/min. This projection was then used as a die to form a groove with a depth and width of about 40 and 50 µm, respectively, on a polyethylene terephthalate plate by pressing.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 805)

Pages:

37-42

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.805.37

Citation:

Cite this paper

Online since:

June 2019

Authors:

Toshio Haga*, Yhuta Nakazawa

Keywords:

A356, Micro-Forming, Rapid Solidification, Roll Casting, Rolling

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] Y. Saotome and A. Inoue, Superplastic microforming of microstructures, Proc.IEEE Micro Electro Mechanical System, Tokyo, (1994) 343-347.

Google Scholar

[2] Y. Saotome, T. Iijima, T. Zhang and A. Inoue, Microforming of metallic glasses with laser micromachined polyimide dies, J. Metastab. Nanocrystal. Mater. 15-16 (2003) 655-658.

DOI: 10.4028/www.scientific.net/jmnm.15-16.655

Google Scholar

[3] Y. Saotome, S. Okaniwa, T. Zhang, A. Inoue, Nanoforming of metallic glass with nano-scale die fabricated by focused ion beam, J. Metastab. Nanocrystal. Mater. 24-25 (2005) 291-294.

DOI: 10.4028/www.scientific.net/jmnm.24-25.291

Google Scholar

[4] M. Ishida, H. Takeda, N. Nishiyama, Y. Shimizu, K. Kita, Y. Saotome, A. Inoue, Characterization of super-precision microgear made of Ni-based metallic glass, J. Metastab. Nanocrystal. Mater. 24-25 (2005) 543-546.

DOI: 10.4028/www.scientific.net/jmnm.24-25.543

Google Scholar

[5] T. Haga, K. Takahashi, M. Ikawa, H. Watari, A vertical type twin roll caster for aluminum alloy strip, J. Mater. Proc. Tech. 140 (2003) 610-615.

DOI: 10.1016/s0924-0136(03)00835-5

Google Scholar

[6] T. Haga, S. Suzuki, Study on a high-speed twin roll caster for aluminum alloys, J. Mater. Proc. Tech. 143 (2003) 895-900.

DOI: 10.1016/s0924-0136(03)00400-x

Google Scholar