Detonation Spraying of Composite Targets Based on Ni, Cr and B₄C for Magnetron Multi-Functional Coating

Abstract:

The paper presents a method of producing a ceramic metal composite target by detonation gas-thermal spraying allowing spraying almost any powder compositions with high deposition efficiency of up to 90% and the possibility of spraying large areas at a relatively low cost, differentiation by coating thickness and size. The efficiency of detonation technology and related devices for the production of original composite cathodes for magnetron sputtering using the example of the powder composition Ni + Cr + B₄C is justified. These materials make it possible to obtain composite coatings with a unique composition and characteristics using a magnetron. Magnetron sputtering is one of the most suitable methods for the industry. The influence of the process mode of metal ceramic powder application on copper substrate is considered. The structure of a metal-ceramic composite target was studied by scanning electron microscopy. It was shown that the target surface is dense without visible pores. The elemental composition of the powder is uniformly distributed over the target surface.

• Periodical: Key Engineering Materials (Volume 909)
• Pages: 115-120
• DOI: https://doi.org/10.4028/p-74w31h
• Online since: February 2022
• Authors: Viacheslav V. Sirota*, Sergey Zaitsev, Dmitriy Prokhorenkov, Michael Limarenko, Andrey Skiba, Marina G. Kovaleva
• Keywords: Microstructure, Multi-Chamber Detonation Device, Multicomponent Targets

References

[1] S. V. Zaitsev, N. I. Cherkashina, V. I. Pavlenko, D. S. Prochorenkov Formation and stability of W coating on a flexible polyimide substrate Thin Solid Films 715 (2020) 138424.

DOI: 10.1016/j.tsf.2020.138424

[2] D. Manova, J.W. Gerlach, S. Mändl Thin film deposition using energetic ions Materials 3 (2010) 4109-4141.

DOI: 10.3390/ma3084109

[3] S. S. Kiparisov, O. V. Padalko Equipment in Powder Metallurgical Enterprises. Metallurgiya Moscow, (1988).

[4] D.V. Shtansky, E.A. Levashov, A.N. Sheveiko, J.J. Moore The Structure and Properties of Ti–B–N, Ti–Si–B–N, Ti–Si–C–N, and Ti–Al–C–N coatings deposited by magnetron sputtering using composite targets produced by self-propagating high-temperature synthesis SHS Journal of Materials Synthesis and Processing. 6(1) (1998) 61–72 https://doi.org/10.1023/A:1022663210694.

DOI: 10.1134/1.1866403

[5] F.V. Kiryukhantsev-Korneev, K.A. Kuptsov, A.N. Sheveiko, E.A. Levashov, D.V. Shtansky Wear-resistant Ti-Al-Si-CN coatings produced by magnetron sputtering of SHS targets Russian Journal of Non-Ferrous Metals 54(4) (2013) 330-335.

DOI: 10.3103/s106782121304007x

[6] P.V. Kiryukhantsev-Korneev, A.N. Sheveyko, K.A. Kuptsov, A.V. Novikov, D.V. Shtansky Ti-Cr-BN coatings prepared by pulsed cathodic-arc evaporation of ceramic TiCrB target produced by SHS Protection of Metals and Physical Chemistry of Surfaces 49(6) (2013) 677-681.

DOI: 10.1134/s2070205113060075

[7] V.V. Vasyliev, A.A. Luchaninov, E.N. Reshetnyak, V.E. Strel'nitskij, G.N. Tolmacheva, G.A. Pribytkov, A.V. Gurskikh, M.G. Krinitcyn Application of powder cathodes for Ti-Si-N coatings deposition from the filtered vacuum-arc plasma Journal of Surface Physics and Engineering 13(2) (2015) 148-163.

DOI: 10.1016/j.surfcoat.2011.09.061

[8] T. Endo, R. Obayashi, T. Tajiri, K. Kimura, Y. Morohashi, T. Johzaki, S. Mizunari, Thermal spray using a high-frequency pulse detonation combustor operated in the liquid-purge mode Journal of Thermal Spray Technology 25(3) (2016) 494-508.

DOI: 10.1007/s11666-015-0354-8

[9] Q. Wang, Q. Sun, M.X. Zhang, W.J. Niu, C.B. Tang, K.S. Wang, L. Wang The influence of cold and detonation thermal spraying processes on the microstructure and properties of Al-based composite coatings on Mg alloy Surface and Coatings Technology 352 (2018) 627-633.

DOI: 10.1016/j.surfcoat.2018.08.045

[10] L.I. Markashova, Y.N. Tyurin, O.V. Kolisnichenko, E.N. Berdnikova, O. S. Kushnareva, E.V. Polovetsky, E.P. Titkov Effect of structure on properties of Al2O3 and Al (or Ti) mechanical mixture coatings produced by multichamber detonation spraying method Paton Weld. J. 9 (2017) 27-32.

DOI: 10.15407/tpwj2017.09.05

[11] M. Kovaleva, M. Prozorova, M. Arseenko, Y. Tyurin, O. Kolisnichenko, M. Yapryntsev, Sirota V. Zircon-based ceramic coatings formed by a new multi-chamber gas-dynamic accelerator Coatings 7(9) (2017) 142.

DOI: 10.3390/coatings7090142