Paper Titles

Investigation of Causes of Wall Thinning during Stamping of Halves of Stamped-Welded Elbows
p.370

Studying on the Internal Quality of Steel at Various Stages of Production: Slab-Rolled Metal
p.377

Design and Manufacturing Technology of Round Samples for Studying the Effect of Defects on the Mechanical Properties of Welds
p.387

Kinetics of the Formation of Bimetallic Compounds and the Distribution of Energy Components in the Explosion Welding Process
p.393

Modeling of High Module Power Sources Systems Safety Processes
p.399

Assessment of Fracture Mechanisms and Temperature of Ductile-Brittle Transition of Metals Obtained on the Basis of 3D Printing Using Neural Network Modeling and Fractal Analysis
p.407

Optimization of 3D Printing Modes for Electric Arc Surfacing Using a Digital Twin of the Process
p.414

Hard Alloys Recycling as a Promising Direction of Technological Equipment for Machine-Building Production
p.423

Methods for the Determination of Chloride-Ion in Soils from the Territory of Nearby Metallurgical Enterprises: Guidelines for Selection
p.429

HomeMaterials Science ForumMaterials Science Forum Vol. 1052Modeling of High Module Power Sources Systems...

Modeling of High Module Power Sources Systems Safety Processes

Article Preview

Abstract:

The paper provides an assessment of the safety processes of high-modulus energy sources systems during the initiation of flat and cylindrical high-modulus energy sources. The expressions, which establish the relationship between the parameters of flat and hollow cylindrical charges of explosives under the only condition of equality of the developed pressure pulse on the surface of the charge of explosives, provided all other things being equal, were obtained. In contrast to the earlier studies, which assert the existence of a direct relationship between the parameters during the initiation of flat and cylindrical surfaces, the current study demonstrates energy consumption during the initiation of cylindrical surfaces is higher than the initiation of flat surfaces, all other things being equal.

You might also be interested in these eBooks

Materials Science and Metallurgical Technology III

Info:

Periodical:

Materials Science Forum (Volume 1052)

Pages:

399-404

DOI:

https://doi.org/10.4028/p-24y9ae

Citation:

Cite this paper

Online since:

February 2022

Authors:

Iurii V. Savchenko, Oleksandr Shapoval*, Ihor Kuziev

Keywords:

Cobalt, Hard Alloy, Heterogeneous Medium, Metal Ceramics, Recycling, Tool, Tungsten

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2022 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

* - Corresponding Author

[1] Iu. Savchenko, A. Gurenko, O. Naumenko. Cutting-edge industrial technology of mining tool manufacturing, Mining of Mineral Deposits. 10(4) (2016) 105-110.

DOI: 10.15407/mining10.04.105

[2] A. Shapoval, I. Savchenko, O. Markov, Determination coefficient of stress concentration using a conformed display on a circle of a single radius, Solid State Phenomena. 316 (2021) 928-935.

DOI: 10.4028/www.scientific.net/ssp.316.928

[3] A. Shapoval, V. Drahobetskyi, I. Savchenko, A. Gurenko, O. Markov, Profitability of production of stainless steel + zirconium metals combination adapters, Key Engineering Materials. 864 (2020) 285-291.

DOI: 10.4028/www.scientific.net/kem.864.285

[4] I. Savchenko, A. Shapoval, A. Gurenko, Modeling dynamic parameters of hard alloys during shock wave regeneration, IOP Conference Series: Materials Science and Engineering. 969(1) (2020) 012079.

DOI: 10.1088/1757-899x/969/1/012079

[5] V. Dragobetskii, M. Zagirnyak, O. Naumova, S. Shlyk, A. Shapoval, Method of determination of technological durability of plastically deformed sheet parts of vehicles, International Journal of Engineering and Technology(UAE). 7 (4) (2018) 92-99.

DOI: 10.14419/ijet.v7i4.3.19558

[6] M. Zagirnyak, V. Zagirnyak, D. Moloshtan, V. Drahobetskyi, A. Shapoval, A search for technologies implementing a high fighting efficiency of the multilayered elements of military equipment, Eastern-European Journal of Enterprise Technologies. 6(1-102) (2019) 33-40.

DOI: 10.15587/1729-4061.2019.183269

[7] A. Shapoval, R. Kantemyrova, O. Markov, A. Chernysh, R. Vakulenko, I. Savchenko, Technology of production of refractory composites for plasma technologies, Proceedings of the 25th IEEE International Conference on Problems of Automated Electric Drive. Theory and Practice (PAEP). (2020) 9240830.

DOI: 10.1109/paep49887.2020.9240830

[8] V.V. Bogoboyashchii, A.P. Vlasov, I.I. Izhnin, Mechanism for conversion of the conductivity type in arsenic-doped p-CdxHg1-xTe subject to ionic etching, Russian Physics Journal. 44(1) (2001) 61-70.

DOI: 10.1023/a:1011312902981

[9] M. Zagirnyak, A. Kalinov, V. Melnykov, I. Kochurov, Correction of the operating modes of an induction motor with asymmetrical stator windings at vector control,  2015 International Conference on Electrical Drives and Power Electronics (EDPE). (2015) 259-265.

DOI: 10.1109/edpe.2015.7325303

[10] M. Zagirnyak, M. Maliakova, A. Kalinov, Analysis of operation of power components compensation systems at harmonic distortions of mains supply voltage, Joint International Conference ‒ ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems. (2015) 355-362.

DOI: 10.1109/optim.2015.7426958

[11] V.V. Bogoboyashchii, I.I. Inzhin, Mechanism for conversion of the type of conductivity inp-Hg1-xCdxTe crystals upon bombardment by low-energy ions, Russian Physics Journal. 43(8) (2000) 627-636.

[12] E. Belas, V.V. Bogoboyashchyy, R. Grill, I. I. Izhnin, A.P. Vlasov, V.A. Yudenkov, Time relaxation of point defects in p- and n-(HgCd)Te after ion milling, Journal of Electronic Materials. 32(7) (2003) 698-702.

DOI: 10.1007/s11664-003-0055-9

[13] M.V. Zagirnyak, V.V. Prus, A.V. Nikitina, Grounds for efficiency and prospect of the use of instantaneous power components in electric systems diagnostics, Przeglad Elektrotechniczny. 82(12) (2006) 123-125.

[14] V. Prus, A. Nikitina, M. Zagirnyak, D. Miljavec, Research of rnergy processes in circuits containing iron in saturation condition, Przeglad Elektrotechniczny. 87(3) (2011) 149-152.

[15] M. Zagirnyak, D. Mamchur, A. Kalinov, Comparison of induction motor diagnostic methods based on spectra analysis of current and instantaneous power signals, Przeglad Elektrotechniczny. 88(12 B) (2012) 221-224.

DOI: 10.1109/secon.2014.6950721

[16] O. Kurpe, V. Kukhar, R. Puzyr, V. Burko, E. Balalayeva, E. Klimov, Electric motors power modes at synchronization of roughing rolling stands of hot strip mill. CONFERENCE 2020, PAEP 510 (2020).

DOI: 10.1109/paep49887.2020.9240818

[17] M. Zagirnyak, D. Mamchur, A. Kalinov, Induction motor diagnostic system based on spectra analysis of current and instantaneous power signals,  IEEE SOUTHEASTCON 2014. (2014).

DOI: 10.1109/secon.2014.6950721

[18] I. Lutsenko, E. Fomovskaya, I. Oksanych, S. Koval, O. Serdiuk, Development of a verification method of estimated indicators for their use as an optimization criterion, Eastern-European Journal of Enterprise Technologies. 2(486) (2017) 17-23.

DOI: 10.15587/1729-4061.2017.95914

[19] V.V. Bogoboyashchyy, A.I. Elizarov, I.I. Izhnin, Conversion of conductivity type in Cu-doped Hg0.8Cd 0.2Te crystals under ion beam milling, Semiconductor Science and Technology. 20(8) (2005) 726-732.

DOI: 10.1088/0268-1242/20/8/013

[20] N. Hrudkina, L. Aliieva, O. Markov, I. Marchenko, A. Shapoval, P. Abhari, M. Kordenko, Predicting the shape formation of hollow parts with a flange in the process of combined radial-reverse extrusion Eastern-European Journal of Enterprise Technologies. 4(1) (106) (2020) 55-62.

DOI: 10.15587/1729-4061.2020.203988

[21] M. Zagirnyak, M. Maliakova, A. Kalinov, Analysis of electric circuits with semiconductor converters with the use of a small parameter method in frequency domain, COMPEL – The International Journal for Computation and Mathematics in Electrical and Electronic Engineering. 34(3) (2015) 808-823.

DOI: 10.1108/compel-10-2014-0260

[22] O. Markov, V. Kukhar, V. Zlygoriev, A. Shapoval, A. Khvashchynskyi, R. Zhytnikov, Improvement of upsetting process of four-beam workpieces based on computerized and physical modeling, FME Transactions. 48(4) (2020) 946-953.

DOI: 10.5937/fme2004946m

[23] N.S. Hrudkina, Process modeling of sequential radial-direct extrusion using curved triangular kinematic module, FME Transactions. 49(1) (2021) 56-63.

DOI: 10.5937/fme2101056h

[24] I. Lutsenko, E. Vihrova, E. Fomovskaya, O. Serdiuk, Development of the method for testing of efficiency criterion of models of simple target operations, Eastern-European Journal of Enterprise Technologies. 2(4) (2016) 42-50.

DOI: 10.15587/1729-4061.2016.66307

[25] I. Lutsenko, Identification of target system operations. Development of global efficiency criterion of target operations, Eastern-European Journal of Enterprise Technologies. 2(2) (2015) 35-40.

DOI: 10.15587/1729-4061.2015.38963

[26] V. Kukhar, A. Grushko, I. Vishtak, Shape indexes for dieless forming of the elongated forgings with sharpened end by tensile drawing with rupture, Solid State Phenomena. 284 (2018) 408-415.

DOI: 10.4028/www.scientific.net/ssp.284.408

[27] A. Grushko, V. Kukhar, Y. Slobodyanyuk, Phenomenological model of low-carbon steels hardening during multistage drawing, Solid State Phenomena. 265 (2017) 114-123.

DOI: 10.4028/www.scientific.net/ssp.265.114

[28] T. Haikova, R. Puzyr, D. Savelov, V. Dragobetsky, R. Argat, R. Sivak, The Research of the morphology and mechanical characteristics of electric bimetallic contacts, CONFERENCE 2020, PAEP. 579 (2020).

DOI: 10.1109/paep49887.2020.9240847

[29] A. Zarapin, A. Shur, N. Chichenev, Improvement of the unit for rolling aluminum strip clad with corrosion-resistant steel, Steel in Translation. 29(10) (1999) 69-71.

[30] O. Khrebtova, A. Shapoval, D. Mos'pan, V. Dragobetsky, S. Gorbatyuk, O. Markov, Automatic temperature control system for electric resistance annealing of steel welding wire, Metallurgist. 65 (2021) 412-422.

DOI: 10.1007/s11015-021-01171-4