A Study of Cut Surface after the Abrasive Water Jet Application on the MS1 Material Prepared by DMLS Method

Abstract:

This contribution deals with the study of cut surface after the abrasive water jet application on the material Maraging Steel MS-1, prepared by the 3D printing method Direct Metal Laser Sintering. The aim of the study is to point out the morphology of the cut plane under the use of various technological parameters, like feed rate of machining and abrasive mass flow at the constant cut pressure. For the track morphology monitoring after the abrasive water jet application, scanning electron microscope was used. For the identification of observed particles stabbed in the cut track, chemical composition EDX analysis was used.

• Periodical: Materials Science Forum (Volume 1082)
• Pages: 195-200
• DOI: https://doi.org/10.4028/p-8b89tg
• Online since: March 2023
• Authors: Radoslav Vandzura*, Vladimír Simkulet, František Botko, Matúš Geľatko
• Keywords: Abrasive Water Jet, Additive Manufacturing, AWJM, DMLS

References

[1] A. R. R. Bineli, A. P. G. Peres, A. L. Jardini, R. Maciel, Direct metal laser sintering (DMLS): Technology for design and construction of microreactors, In: 6º CONGRESS OBRASILEIRO DE ENGENHARIA DE FABRICA ÇÃO (Vol. 11). Filho (2011, April).

[2] T. Duda, L. V. Raghavan, 3D metal printing technology. IFAC-PapersOnLine, 49 (29) (2016) 103-110.

DOI: 10.1016/j.ifacol.2016.11.111

[3] M. Shellabear, O. Nyrhilä, DMLS-Development history and state of the art. laser assisted netshape engineering 4, Proceedings of the 4th LANE, (2004) 21-24.

[4] Information on: https://additivemanufacturingllc.com/uncategorized/dmls-vs-sls-which-is-better-for-your-needs/.

[5] J. Dobransky, P. Baron, V. Simkulet, M. Kočiško, J. Ružbarský, E. Vojnová, Examination of material manufactured by direct metal laser sintering (DMLS). Metalurgija, 54 (3) (2015) 477-480.

[6] Information on: https://cdn.eos.info/04f875d5141d28f7/8ecee6ee388d/MS-MS1-M270-M280_200W_Material_data_sheet_05-14_en.pdf.

[7] Information on: https://www.eos.info/en/additive-manufacturing/3d-printing-metal.

[8] K. Monková, Some aspects of DMLS technology, RISE Association (2017) p.117.

[9] T. M. Mower, M. J. Long, Mechanical behavior of additive manufactured, powder-bed laser-fused materials, Mat. Sci & Eng. (2015).

[10] S. Rahmati, Advances in Additive Manufacturing and Tooling. Comprehensive Materials Processing, 10 (2014) 303-344.

[11] V. Simkulet, D. Dupláková, A. Kovalčíková, M. Hatala, M., Botko, Z. Mitaľová, Evaluation of tribological characteristics of material prepared by DMLS technology. MM Publishing Vol. 2021-October, 4941-4945.

[12] J. Valícek, M. Harnicarova, A. Panda, I. Hlavatý, M. Kušnerová, H. Tozan, M. Yagimli, V. Václavík, Mechanism of Creating the Topography of an Abrasive Water Jet Cut Surface. Machining, joining and modifications of advanced materials, 61 (2016) 111-120.

DOI: 10.1007/978-981-10-1082-8_12

[13] K. Monková, I. Zetková, L. Kučerová, M. Zetek, P. Monka, M. Daňa, Study of 3D printing direction and effects of heat treatment on mechanical properties of MS1 maraging steel. Arch. of Appl. Mech. 89 (2019) 791-804.

DOI: 10.1007/s00419-018-1389-3

[14] G. Ozer, A. Karaaslan, A Study on the Effects of Different Heat-Treatment Parameters on Microstructure–Mechanical Properties and Corrosion Behavior of Maraging Steel Produced by Direct Metal Laser Sintering. WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. Steel Research int. 2020, 91 (2020) 2000195.

DOI: 10.1002/srin.202000195

[15] J. Dobránsky, M. Kočiško, P. Baron, V. Simkulet, L. Běhálek, E. Vojnová, L. Nováková-Marcinčinová, Evaluation of the impact energy of the samples produced by the additive manufacturing technology, Metalurgija, 55 (3) (2016) 477-480.

[16] V. Simkulet, O. Gusak, J. Zajac, Ľ. Parilák, Z. Mitaľová, Verifikácia procesu tepelného spracovania materiálu vyrobeného technológiou priameho spekania laserom. Automatizácia a riadenie v teórii a praxi: ARTEP TU Košice. (2018) 1-7 (In Slovak).