Microstructural Characterisation of Railhead Damage in Insulated Rail Joints

C. Rathod; D. Wexler; T. Chandra; H. Li

doi:10.4028/www.scientific.net/MSF.706-709.2937

Paper Titles

Diffusion Behavior and Interfacial Reaction of Heterogeneous Metal Systems Controlled by High Magnetic Fields
p.2910

Single Photon Generation from Nitrogen Atomic-Layer Doped Gallium Arsenide
p.2916

Dynamic Resistance Based Model for On-Line Resistance Spot Welding Quality Assessment
p.2925

Specific Energy as a Characterizing Parameter for Laser Welded Ti-5Al-5V-5Mo-3Cr Alloy
p.2931

Microstructural Characterisation of Railhead Damage in Insulated Rail Joints
p.2937

Simplified Simulation of the Friction Stir Welding Process. Influence of the Boundary Conditions Modelling
p.2943

Experimental and Numerical Investigation of Residual Stress and Distortion Control during Welding of AISI-316L Plates
p.2950

Laser Joining of Metal and Plastic Using Insert Materials
p.2956

Low Temperature Sintering Bonding Process Using Ag Nanoparticles Derived from Ag₂O for Packaging of High-Temperature Electronics
p.2962

HomeMaterials Science ForumMaterials Science Forum Vols. 706-709Microstructural Characterisation of Railhead...

Microstructural Characterisation of Railhead Damage in Insulated Rail Joints

Abstract:

As an integral part the railway network infrastructure, insulated rail joints (IRJs) electrically isolate track segments providing critical feedback to both track signaling and train position detection systems. Because of the discontinuous nature of IRJs, accumulated damage at the railhead is high. Failure modes include plastic flow of metal across joints, bolt and fishplate failures, delamination of insulated material and, as a result of rolling contact fatigue, end post and endpost surface damage. In the current investigation, microstructural changes in the vicinity of endposts of IRJs made from both surface coated and uncoated rail are investigated using techniques of optical and scanning electron microscopy. Damaged IRJs made from pearlitic head hardened rail steel are compared with head hardened rail steel laser coated with martensitic stainless steel, the latter having an increased service life. Problems associated with the surface coating are identified and approaches to further improving IRJ resistance to rolling contact fatigue suggested. Keywords: Insulated rail joints, rail, head hardened, surface coated rail

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Materials Science Forum (Volumes 706-709)

Pages:

2937-2942

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.706-709.2937

Citation:

Cite this paper

Online since:

January 2012

Authors:

C. Rathod, D. Wexler, T. Chandra, H. Li

Keywords:

Head Hardened, Insulated Rail Joints, Rail, Surface Coated Rail

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] D. Peltier, C.P.L. Barkan, S. Downing, D. Socie: Measuring degradation of bonded insulated rail joints, University of Illinois at Urbana-Champaign, Urbana, IL 61801.

DOI: 10.3934/jcd.2019003

Google Scholar

[2] S.W. Huang, S. Burgess, L. N. Wehrmann, D. Nolan and T. Chandra; Insulated rail joints for signalling applications, Proc. THERMEC 2006 Int. Conf. on Processing & Manufacturing of Advanced Materials, Ed. T. Chandra et al., Trans Tech. (2006).

Google Scholar

[3] Y. Hiroto: Development of a long life Insulated Rail Joint, Quarterly reports of the Railway Technical Research, Vol. 25 (1984) p.79.

Google Scholar

[4] C. Smalley: Preliminary study into fatigue of Insulated Rail Joints, Institute of Railway Technology at Monash University, (2009).

Google Scholar

[5] Z. Wen, X. Jin, W. Zhang: Contact-impact stress analysis of rail joint region using the dynamic finite element method, Wear, Vol. 258 (2005), p.1301.

DOI: 10.1016/j.wear.2004.03.040

Google Scholar

[6] D.C. Peltier, C.P.L. Barkan: Characterizing and inspecting for progressive epoxy, Journal of the Transportation Research Record, Vol. 11, (Dec 2009) p.85.

DOI: 10.3141/2117-11

Google Scholar

[7] J. Igwemezie, A.T. Nguyen: Anatomy of joint bar failures II, Railway Track & Structures, Vol. 105, Issue 10, (Oct 2009) p.43.

Google Scholar

[8] J. Igwemezie, A.T. Nguyen: Anatomy of joint bar failures III, Railway Track & Structures, Information on http: /www. rtsnds. com, (Feb 2010).

Google Scholar

[9] V. Reddy : Modelling and Analysis of Rail Grinding & Lubrication strategies for Controlling Rolling Contact fatigue(RCF) and Rail Wear, Master of Applied Science Thesis, Queensland University of Technology, (May, 2004).

Google Scholar

[10] J.J. Han, M. Dhanasekar: A method for tracking internal crack propagation in railhead, International Journal of Fracture, Vol. 130, (2004) p.705.

DOI: 10.1007/s10704-004-2508-4

Google Scholar

[11] Tao. Pang: Studies on Wheel/Rail contact-Impact forces at the Insulated rail Joints, Master of Engineering Thesis, Central Queensland University, Australia ( June, 2007).

Google Scholar

[12] A.K. Himebaugh, R.H. P, D.A. Dillard: Finite element analysis of bonded insulated rail joints, International journal of Adhesion & Adhesives, Vol. 28, (2008), p.142.

DOI: 10.1016/j.ijadhadh.2007.09.003

Google Scholar

[13] B. Talamini, D.Y. Jeong, J. Gordon, Estimation of the fatigue life of railroad joint bars, Proceedings of Joint Rail Conference & Internal Combustion Engine Spring Technical Conference, Colorado, USA, ( March, 2007).

DOI: 10.1115/jrc/ice2007-40065

Google Scholar

[14] R.H. Plaut, H.L. Busch, A. Eckstein, S. Lambrecht, D.A. Dillard: Analysis of tapered, adhesively bonded, insulated rail joints, Proceedings of the Institution of Mechanical Engineers, Vol. 221 (Jun 2007) p.195.

DOI: 10.1243/0954409jrrt107

Google Scholar