Analytical Modeling to Predict Adiabatic Shear Critical Condition for Orthogonal Cutting

Abstract:

As the deformation of chip increases with cutting speed, the morphology of chip changes from continuous to serrated type. It is supposed that serrated chips generate due to adiabatic shear instability in the primary deformation zone. A new analytical model for predicting adiabatic shear critical condition in orthogonal cutting is proposed by considering cutting conditions and properties of workpiece material. It is found that the influence of shear strain on the onset of adiabatic shear could be neglected. The shear strain rate and temperature, however, play a leading role on the onset of adiabatic shear. At lower cutting speed the shear strain rate plays a dominant role while at higher cutting speed the situation is just the reverse. With the increase of cutting speed, the yield stress, material characteristic constant and uncut chip thickness will facilitate adiabatic shear instability, while the coefficient of strain rate hardening, coefficient of strain hardening, coefficient of thermal softening, thermal diffusivity and tool rake angle have negative effect on adiabatic shear instability.

• Periodical: Materials Science Forum (Volume 723)
• Pages: 41-49
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.723.41
• Online since: June 2012
• Authors: Qi Biao Yang, Zhan Qiang Liu, Zhen Yu Shi
• Keywords: Adiabatic Shear, Critical Condition, Orthogonal Cutting, Ti6Al4V

References

[1] G. Li, M. Wang and C. Duan: J. Mater. Process. Technol. Vol. 209 (2009), p.1362.

[2] H. Schulz, E. Abele and A. Sahm: CIRP Ann. Manuf. Technol. Vol. 50 (2001), p.45.

[3] B. John and B. Gerald: J. Manuf. Sci. Eng. Vol. 124 (2002), p.528.

[4] A. Molinari, C. Musquar and G. Sutter: Int. J. Plast. Vol. 18 (2002), p.443.

[5] R. Komaduri and Z. Hou: Metall. Mater. Trans. A Vol. 33A (2002), p.2995.

[6] M.D. Morehead, Y. Huang and J. Luo: Mach. Sci. Technol. Vol. 11 (2007), p.335.

[7] R.F. Recht: J. Appl. Mech. Vol. 31 (1964), p.189.

[8] D. Lee: J. Eng. Mater. Technol. Vol. 106 (1984), p.9.

[9] J.Q. Xie, A.E. Bayoumi and H.M. Zbib: J. Mater. Eng. Perform. Vol. 4 (1995), p.32.

[10] J. Huang, K. Kalaitzidou, J.W. Sutherland et al: J. Mech. Behav. Mater. Vol. 18 (2007), p.243.

[11] N. Tounsi, J. Vincenti, A. Otho et al: Int. J. Mach. Tools Manuf. Vol. 42 (2002), p.1373.

[12] P.L.B. Oxley: The mechanics of machining: an analytical approach to assessing machinability (Halsted Press, USA 1989).

[13] A. O. Tay, M.G. Stevenson, G.D.V. Davis et al: Int. J. Mach. Tool Des. Res. Vol. 16 (1976), p.335.

[14] E.G. Loewen and M.C. Shaw: Trans. ASME Vol. 76 (1954), p.217.

[15] Z. Liu, J. Wu, Z. Shi et al: Tool Eng. Vol. 42 (2008), p.3.

[16] X. Ai: Technology of high speed cutting (National Defense Industrial Press, Beijing 2003).

[17] R. Komaduri and V.B.F. Turkovich: Wear Vol. 69 (1981), p.179.