Crushing Response of Green Square Honeycomb Structure from Sugar Palm &amp; PLA

Zahidah Ansari; Mohd Ruzaimi Mat Rejab; Dandi Bachtiar; Januar Parlaungan Siregar

doi:10.4028/www.scientific.net/MSF.909.122

Paper Titles

Wear Behavior of In Situ Mg₂Si Particle-Dispersed Magnesium Alloys
p.100

Investigation of Friction Coefficient for Twaron-Reinforced Brake Shoe Materials
p.106

A Study of the Structural and Mechanical Characterization of Hybrid Nanocomposite Material
p.111

Fabrication of Al-Based Composites Cylinder Reinforced with In Situ Si/Mg₂Si Particles and the Research of its Bench Test
p.116

Crushing Response of Green Square Honeycomb Structure from Sugar Palm & PLA
p.122

Bending Behavior and Electrical Conductivity of Cu/Ni/Al/Ni/Cu Clad Composite
p.127

Fracture Analysis for Attaching Fiber Reinforced Composite on V-Notch Wedge Structure
p.133

Effect of Calcium Ion Crosslinked Alginate Based Coating on Flame Retardancy of Polyester-Cotton Fabric
p.145

Fabrication of Micro Fluidic Channels in Polymers by Melt-Electrospinning
p.151

HomeMaterials Science ForumMaterials Science Forum Vol. 909Crushing Response of Green Square Honeycomb...

Crushing Response of Green Square Honeycomb Structure from Sugar Palm & PLA

Abstract:

Experiment investigation were conducted on square honeycomb structure made out of sugar palm reinforced polylactic acid (PLA). This paper investigate the compression and tensile properties of new and recycled sugar palm/PLA composite. Short fiber were obtain by crushing and then mix with PLA before being hot pressed at 180°C. The 3mm plate were then developed into sandwich square honeycomb structure. The result show small decrement in strength pattern.

You might also be interested in these eBooks

5th Asia Conference on Mechanical and Materials Engineering

View Preview

Info:

Periodical:

Materials Science Forum (Volume 909)

Pages:

122-126

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.909.122

Citation:

Cite this paper

Online since:

November 2017

Authors:

Zahidah Ansari, Mohd Ruzaimi Mat Rejab*, Dandi Bachtiar, Januar Parlaungan Siregar

Keywords:

Compression Properties, Polylactic Acid (PLA), Sugar Palm Fibre, Tensile Properties, Young’s Modulus

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] X. Tian, T. Liu, Q. Wang, A. Dilmurat, D. Li, and G. Ziegmann, Recycling and remanufacturing of 3D printed continuous carbon fi ber reinforced PLA composites, J. Clean. Prod., vol. 142, p.1609–1618, (2017).

DOI: 10.1016/j.jclepro.2016.11.139

Google Scholar

[2] C. Baumgart, D. Ehinger, C. Weigelt, L. Krüger, and C. G. Aneziris, Comparative study of TRIP / TWIP assisted high density composite honeycomb structures under compressive load, Compos. Struct., vol. 136, p.297–304, (2016).

DOI: 10.1016/j.compstruct.2015.09.053

Google Scholar

[3] K. P. Dharmasena et al., European Journal of Mechanics A / Solids Dynamic compression of metallic sandwich structures during planar impulsive loading in water, Eur. J. Mech. / A Solids, vol. 29, no. 1, p.56–67, (2010).

DOI: 10.1016/j.euromechsol.2009.05.003

Google Scholar

[4] S. M. Sapuan and D. Bachtiar, Mechanical Properties of Sugar Palm Fibre Reinforced High Impact Polystyrene Composites, vol. 4, p.101–106, (2012).

DOI: 10.1016/j.proche.2012.06.015

Google Scholar

[5] B. Rashid, Z. Leman, M. Jawaid, M. J. Ghazali, and M. R. Ishak, The Mechanical Performance of Sugar Palm Fibres ( Ijuk ) Reinforced Phenolic Composites, vol. 17, no. 8, p.1001–1008, (2016).

DOI: 10.1007/s12541-016-0122-9

Google Scholar