Cleaning Optimization of Hot-Dip Galvanized Steel Surfaces in Preparation for Paint Application

Abstract:

Hot-dip galvanized steel surfaces are cleaned, pre-treated with titanium-containing solution and then painted for use. Removal of the alumina layer from galvanized steel surfaces during the cleaning process is essential before effective paint application. Bad adhesion results if the alumina layer is not completely removed, and an insufficient concentration and uneven distribution of titanium oxide is formed across the galvanized surface during pre-treatment. The alkaline cleaner concentration must be optimized to ensure effective removal of the alumina layer. Hot-dip galvanized steel samples were cleaned using typical line conditions and cleaning solutions with varying free alkalinities. The alumina layer was then measured on each sample by glow-discharge optical emission spectroscopy. Thereafter, the samples were treated with titanium-containing pre-treatment solution. The titanium oxide concentration was measured by inductively coupled plasma optical emission spectroscopy. It was found that a free alkalinity of at least 3.2 mEq/L is required to fully remove the alumina layer. The alumina-free samples also gave a titanium oxide layer after pre-treatment within the target concentration of 4–8 mg/cm². A free alkalinity of 3.5 ml was thereafter implemented commercially: analysis of samples from two galvanizing lines showed no presence of alumina, a uniform titanium oxide distribution across the widths of the line samples and acceptable titanium concentrations.

• Periodical: Materials Science Forum (Volume 941)
• Pages: 1772-1777
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.941.1772
• Online since: December 2018
• Authors: Liezl Schoeman*, Marc Burty
• Keywords: Alumina, Galvanized, Paint, Titanium

References

[1] V. Saarimaa, A. Markkula, J. Juhanoja, B. Skrifvars, Novel insight to aluminium compounds in the outermost layers of hot dip galvanized steel and how they affect the reactivity of the zinc surface, Surface and Coatings Technology 306 (2016) 506-511.

DOI: 10.1016/j.surfcoat.2015.11.014

[2] V. Saarimaa, A. Kaleva, J. Nikkanen, S. Heinonen, E. Levänen, P. Väisänen, A. Markkula, J. Juhanoja, Supercritical carbon dioxide treatment of hot dip galvanised steel as a surface treatment before coating, Surface and Coatings Technology 331 (2017) 137-142.

DOI: 10.1016/j.surfcoat.2017.10.047

[3] B. Del Amo, L. Véleva, A.R. Di Sarli, C.I. Elsner, Performance of coated steel systems exposed to different media part I. Painted galvanized steel, Progress in Organic Coatings 50 (2004) 179-192.

DOI: 10.1016/j.porgcoat.2004.02.003

[4] V. Saarima, E. Kauppinen, A. Markkula, J. Juhanoja, B. Skrifvars, P.Steen, Microscale distribution of Ti-based conversion layer hot dip galvanized steel, Surface and Coatings Technology 206 (2012) 4173-4179.

DOI: 10.1016/j.surfcoat.2012.04.017

[5] V.Leroy, Metallurgical applications of surface analytical techniques, Materials Science and Engineering 42 (1980) 289-307.

DOI: 10.1016/0025-5416(80)90039-7

[6] R. Berger, U. Bexell, N.Stavlid, T.M. Grehk, The influence of alkali-degreasing on the chemical composition of hot-dip galvanized steel surfaces, Surface and Interface Analysis 38 (2006) 1130-1138.

DOI: 10.1002/sia.2364

[7] M. Wolpers, J.Angeli, Activation of galvanized steel surfaces before zinc phosphating – XPS and GDOES investigations, Applied Surface Science 179 (2001) 281-291.

DOI: 10.1016/s0169-4332(01)00296-3

[8] R. Sako, J. Sakai, Effect of curing temperature on coating structure and corrosion resistance of ammonium zirconium carbonate on galvanized steel surface, Surface and Coatings Technology 219 (2013) 42-49.

DOI: 10.1016/j.surfcoat.2012.12.050

[9] S. Le Manchet, D.Verchère, J. Landoulsi, Effects of organic and inorganic treatment agents on the formation of conversion layer on hot-dip galvanized steel: an x-ray photoelectron study, Thin Solid Films 520 (2012) 2009-2016.

DOI: 10.1016/j.tsf.2011.09.064