Experimental Study of Energy Force Parameters of Combined Process "Rolling - ECA-Pressing"

Abstract:

The article is devoted to the study of energy-force parameters of combined process "rolling-equal-channel angular pressing". The objectives of the work were to determine the forces of rolling and pressing in the deformation by this combined method. The strength calculation of the matrix and the experiment on deformation of AISI 6063 aluminum samples were carried out. During the experiment, the force values were recorded using a tensometric station. The results of the strength analysis showed that this matrix design is suitable for creating an experimental stand of combined process "rolling – equal-channel angular pressing", since the calculated safety margin is sufficient to implement the pressing under extreme conditions. Analysis of the results of force measurement showed that rolling forces at all stages of deformation exceed the corresponding pressing forces, which is a necessary condition for the implementation of this combined process. The obtained results can be used in the design of experimental stands that implement investigated combined process. At the same time, the used tensometric technique for studying strength characteristics is suitable for the case of calibrated rolls.

• Periodical: Materials Science Forum (Volume 946)
• Pages: 850-855
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.946.850
• Online since: February 2019
• Authors: Abdrakhman B. Naizabekov, Sergey N. Lezhnev*, Evgeniy Panin
• Keywords: Combined Process, Equal Channel Angular Pressing, Force, Rolling, Strength Analysis, Tensometry

References

[1] M. Jahedi, M. Knezevic, M.H. Paydar, High-Pressure Double Torsion as a Severe Plastic Deformation Process: Experimental Procedure and Finite Element Modeling, J. Mater. Eng. Perform. 24 4 (2015) 1471-1482.

DOI: 10.1007/s11665-015-1426-0

[2] A. Alhamidi, Z. Horita, Grain refinement and high strain rate superplasticity in alumunium 2024 alloy processed by high-pressure torsion, Mater. Sci. Eng. A. 622 (2015) 139-145.

DOI: 10.1016/j.msea.2014.11.009

[3] R.Z. Valiev, T.G. Langdon, Principles of equal-channel angular pressing as a processing tool for grain refinement, Prog. Mater Sci. 51 (2006) 881-981.

DOI: 10.1016/j.pmatsci.2006.02.003

[4] M.H. Shaeri, M.T. Salehi, S.H. Seyyedein, M.R. Abutalebi, J.K. Park, Microstructure and mechanical properties of Al-7075 alloy processed by equal channel angular pressing combined with aging treatment, Mater. Des. 57 (2014) 250-257.

DOI: 10.1016/j.matdes.2014.01.008

[5] Zhang Xiaohua, Liu Xiaojing, Wang Jingze, Cheng Yuansheng, Effect of route on tensile anisotropy in equal channel angular pressing, Mater. Sci. Eng. A. 676 (2016) 65-72.

DOI: 10.1016/j.msea.2016.08.108

[6] J.G. Kim, M. Latypov, N. Pardis, Y.E. Beygelzimer, H.S. Kim, Finite element analysis of the plastic deformation in tandem process of simple shear extrusion and twist extrusion, Mater. Des. 83 (2015) 858-865.

DOI: 10.1016/j.matdes.2015.06.034

[7] Sh Ranj Bar Bahadori, K. Dehghani, S. A. A. Akbari Mousavi. Comparison of microstructure and mechanical properties of pure copper processed by twist extrusion and equal channel angular Pressing. Mater. Lett. 152 (2015) 48-52.

DOI: 10.1016/j.matlet.2015.03.063

[8] Russian Patent № 2181314.

[9] A.B. Naizabekov, S.N. Lezhnev, I.E. Volokitina, Change in Copper Microstructure and Mechanical Properties with Deformation in an Equal Channel Stepped Die, Met. Sci. Heat Treat. 57 5-6 (2015) 254-260.

DOI: 10.1007/s11041-015-9870-x

[10] Kazakhstan Patent № 25863.

[11] A. Naizabekov, S. Lezhnev, E. Panin, T. Koinov. Theoretical grounds of the combined rolling - equal - channel step pressing, process, J. Chem. Technol. Metall. 51 5 (2016) 594-602.

[12] S.N. Lezhnev, A.B. Naizabekov, Ye.A. Panin, Theoretical studies of the joint extrusion-rolling, process aimed at making sub-ultra fine - grained structure metal, 20th Anniversary International Conference on Metallurgy and Materials (Metal 2011), May 18-20.2011, Brno, Czech Republic, 272-277.

[13] S. Lezhnev, E. Panin, Investigation of the Influence of Geometric and Technological Factors on the Stress-Strain State of Metal in the Implementation of the Combined Rolling-Pressing Process, Adv. Mat. Res. 936 (2014) 1918-1924.

DOI: 10.4028/www.scientific.net/amr.936.1918

[14] S. Lezhnev, A. Naizabekov, E. Panin, T. Koinov, I. Mazur, A. Arbuz, Evaluation of the effectiveness of the use of horizontal and vertical rolls in the Rolling-pressing, process on the basis of the stress-strain state studying, IOP Conf. Ser. Mater. Sci. Eng. 179 (2017) 012047.

DOI: 10.1088/1757-899x/179/1/012047

[15] A. Naizabekov, S. Lezhnev, E. Panin, T. Koinov, Study of broadening in a combined process rolling-pressing, using an equal-channel step die. J. Chem. Technol. Metall. 50 3 (2015) 308-313.

[16] S. Lezhnev, E. Panin, I. Volokitina, Research of combined process Rolling-pressing, influence on the microstructure and mechanical properties of aluminium, Adv. Mat. Res. 814 (2013) 68-75.

DOI: 10.4028/www.scientific.net/amr.814.68

[17] A. Naizabekov, S. Lezhnev, E. Panin, I. Volokitina, Influence of Combined Process Rolling-pressing, on Microstructure and Mechanical Properties of Copper. Proc. Eng. 81 (2014) 1499–1504.

DOI: 10.4028/www.scientific.net/amr.814.68

[18] A. Naizabekov, S. Lezhnev, E. Panin, I. Volokitina, The Role of Preliminary Heat Treatment in the Formation of Ultrafine-Grained Structure in the Implementation of the Combined Process Rolling - Equal Channel Angular Pressing,, Mater. Sci. Forum, 879 (2016) 1093-1098.

DOI: 10.4028/www.scientific.net/msf.879.1093

[19] Information on http://kompas.ru.

[20] Information on http://www.zetlab.ru.