Evaluation of the Effectiveness of Plasma Torches Design for Metal Cutting by Qualimetric Method

I.Y. Matushkina; S.V. Anakhov; Yu.A. Pyckin

doi:10.4028/www.scientific.net/MSF.946.877

Paper Titles

Experimental Study of Energy Force Parameters of Combined Process "Rolling - ECA-Pressing"
p.850

Texture Evolution during Hot Deformation of Al-Cu-Li-Mg-Zn-Zr-Sc Alloy
p.856

Residual Stresses in Elastoplastic Bending of Round Bar
p.862

Tubes’ Rupture at Faulty Fusion of Welding Seam
p.868

Evaluation of the Effectiveness of Plasma Torches Design for Metal Cutting by Qualimetric Method
p.877

Conditions of Possible Application of Vibration Processing in the Course of Welding
p.883

Calculation of Modes of Arc Welding under the Flux of Double-Sided Butt Joints
p.889

The Influence of the Electrode Extension on the Welding-Technological Characteristics of Pulsed Arc Welding Using Cored Wire
p.895

Research of Laser Welding of Thin-Sheet Structural Steels by Pulsed Laser Radiation
p.901

HomeMaterials Science ForumMaterials Science Forum Vol. 946Evaluation of the Effectiveness of Plasma Torches...

Evaluation of the Effectiveness of Plasma Torches Design for Metal Cutting by Qualimetric Method

Abstract:

For experimental substantiation of plasmatrons work efficiency the technological regulations of quality and safety parameters test for plasma-arc cutting of metals technology are taken. For the integral evaluation of the obtained results it is proposed to use the methods of qualimetric analysis adapted to the technology of plasma cutting. The obtained integral parameters indicate the effectiveness of the new plasmatrons, designed by the authors in comparison with previously produced analogues, as well as with modern domestic and foreign samples.

You might also be interested in these eBooks

Materials Science and Metallurgical Technology

View Preview

Info:

Periodical:

Materials Science Forum (Volume 946)

Pages:

877-882

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.946.877

Citation:

Cite this paper

Online since:

February 2019

Authors:

I.Y. Matushkina*, S.V. Anakhov, Yu.A. Pyckin

Keywords:

Design, Destruction, Efficiency, Heat-Affected Zone, Impact Elasticity, Plasmatron, Quality, Static Curve, Welding Seam

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] S.V. Anakhov. Principles and methods of designing in electroplasma and welding technologies, RSVPU, Yekaternburg, (2014).

Google Scholar

[2] S.V. Anakhov, Yu.A. Pykin, Plasma torches: the problem of acoustic safety. Thermophysical and gas-dynamic design principles of low noise plasma torches, Ekaterinburg, RIO Uro RAN, (2012).

DOI: 10.1533/wint.2005.3474

Google Scholar

[3] Anakhov S.V., Pykin. Yu.A., Matushkin, A.V. Narrow Jet Plasma as the Energy Efficient and Safe Technology for Metal Cutting, Solid State Phenomena (Material Science Forum). 870 (2016) 523-527.

DOI: 10.4028/www.scientific.net/msf.870.523

Google Scholar

[4] M.F. Zhukov, A.S. An'shakov, Fundamentals of calculating the linear plasma torches. Novosibirsk: Institute of Thermal physics, Siberian Division of the Ration Academy of Sciences; (1979).

Google Scholar

[5] S.V. Anakhov, Yu.A. Pykin, A.V. Matushkin, Investigation of systems for gas vortex stabilization of plasma torches, Welding International. 30(4) (2016) 310-314.

DOI: 10.1080/01431161.2015.1058005

Google Scholar