Fusion Welding of Rheocast Semi-Solid Metal (SSM) Processed Aluminium Alloy 7017

Abstract:

Near-net shape casting of wrought aluminium alloys has proven to be difficult due to a tendency towards hot tearing during cooling. Rheocasting, or semi-solid metal (SSM) processing followed by high pressure die casting (HPDC), has recently been shown to be an effective alternative to conventional die casting, yielding near-net shape wrought aluminium alloy castings with less risk of hot tearing. This casting process involves pouring the liquid metal into a processing cup, which is then transferred into a coil for induction stirring and simultaneous forced air cooling. When the metal reaches the semi-solid casting temperature, the resultant slurry is transferred to a high pressure die casting machine and cast to near-net shape. This modifies the as-cast microstructure, yielding a more globular primary phase and results in mechanical properties in the -T6 condition closely approaching those of wrought material in the same condition. Little information is currently available on the response of SSM-HPDC material to welding. This project investigated the influence of autogenous laser and gas tungsten arc welding on the microstructure and mechanical properties of aluminium 7017 after rheocasting. It is possible to successfully weld this material without solidification or liquation cracking. The effect of welding on the rheocast microstructure in the heat-affected zone and weld metal was shown, and the hardness and tensile properties of the resulting joints in the as-welded condition were tested and related to the microstructures achieved.

• Periodical: Solid State Phenomena (Volumes 192-193)
• Pages: 161-166
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.192-193.161
• Online since: October 2012
• Authors: Madeleine du Toit, Patronica Letsoalo, Heinrich Möller
• Keywords: Aluminum (Al), Arc Welding, Laser Welding, Semi-Solid Metal Processing (SSM)

References

[1] A.E. Paterson, Introduction to Aluminium, Aluminium Federation of South Africa, Johannesburg, 2007.

[2] J.T. Staley, D. Apelian, Vacuum die-casting of wrought 7050 aluminium alloy, Proc. Materials Solutions Conf, Indianapolis, November 2001, 290-297.

[3] J. Langlais, N. Andrade, A. Lemieux, X.G. Chen, L. Bucher, The semi-solid forming of an improved AA6061 wrought aluminium alloy composition, Diffus De B. 141-143 (2008), 511-516.

DOI: 10.4028/www.scientific.net/ssp.141-143.511

[4] U.A. Curle, Semi-solid near-net shape rheocasting of heat treatable wrought aluminium alloys, Trans. Nonferrous Met. Soc. China 20 (2010) 1719-1724.

DOI: 10.1016/s1003-6326(09)60364-2

[5] H. Möller, G. Govender, W.E. Stumpf, Comparison of the heat treatment response of SSM-HPDC 6082 and 6004 wrought alloys with A356 and F357 casting alloys, Mater. Sci. Forum 690 (2011) 53-56.

DOI: 10.4028/www.scientific.net/msf.690.53

[6] L.H. Ivanchev, J.D. Wilkins, G. Govender, Method and apparatus for rheo-processing of semi-solid metal alloys, Proc 8th International Conference on Semi-Solid Processing of Alloys and Composites, Limassol, Cyprus, 2004, 595-601.

[7] Y.L. Kang, L.Q. Yang, R.B. Song, F. Zhang, T. Tao, Study on microstructure-processing relationship of a semi-solid rheocasting A357 aluminium alloy, Diffus De B. 141-143 (2008) 157-162.

DOI: 10.4028/www.scientific.net/ssp.141-143.157

[8] T. Ma, G. Den Ouden, Softening behaviour of Al-Zn-Mg alloys due to welding, Mat.Sci. Eng. A-Struct. 266 (1999) 198-204.

DOI: 10.1016/s0921-5093(99)00020-9

[9] M. Nicolas, A. Deschamps, Precipitate microstructures and resulting properties of Al-Zn-Mg metal inert gas-weld heat-affected zones, Metall. Mater. Trans. A. 35A (2004) 1437-1448.

DOI: 10.1007/s11661-004-0252-z

[10] Z.-J. Lu, W.J. Evans, J.D. Parker, S. Birley, Simulation of microstructure and liquation cracking in 7017 aluminium alloy, Mat.Sci. Eng. A-Struct. 220 (1996) 1-7.

DOI: 10.1016/s0921-5093(96)10458-5

[11] W. Hepples, M.C. Thornton, N.J.H. Holroyd, Microstructural characterization of "white zones" in weldable 7000 series alloys, J. Mater. Sci. 27 (1992) 5720-5726.

DOI: 10.1007/bf01119728

[12] H. Möller, U.A. Curle, E.P. Masuku, Characterization of surface liquid segregation in SSM-HPDC aluminium alloys 7075, 2024, 6082 and A201, Trans. Nonferrous Met. Soc. China, 20 (2010), 847-851.

DOI: 10.1016/s1003-6326(10)60593-6

[13] H. Möller, The heat treatment of rheo-high pressure die cast Al-Zn-Mg alloy 7017: Submitted to Solid State Phenomena (2012).

DOI: 10.4028/www.scientific.net/ssp.192-193.155

[14] Polmear, I., Light alloys: From traditional alloys to nanocrystals, Butterworth-Heinemann, Amsterdam, 2006.