Model Testing of the 2nd Phase of Die Casting Process

Rafał Dańko; Jerzy Stojek

doi:10.4028/www.scientific.net/SSP.208.52

Paper Titles

Application of CFD in Hydraulic Directional Valve Modeling
p.8

Wave Packet as a Model of Localised Disturbances Propagating along the Cables
p.20

Development of Laboratory Model of Wind Turbine's Tower-Nacelle System with Magnetorheological Tuned Vibration Absorber
p.40

Model Testing of the 2^nd Phase of Die Casting Process
p.52

FEM Analysis of a Cantilever Sandwich Beam with MR Fluid Based on ANSYS
p.63

Diagnosis of Supporting Structures of HV Lines Using Magneto-Mechanical Effects
p.70

Experimental Tests of an Electromechanical Transducer of Reverse Linear Motion into Electrical Energy
p.86

A Project of a System for Measuring Child's Foot Pressure on a Shoe Sole
p.93

HomeSolid State PhenomenaSolid State Phenomena Vol. 208Model Testing of the 2nd Phase of Die Casting...

Model Testing of the 2^nd Phase of Die Casting Process

Abstract:

nvestigations of filling the model mould cavity (with perpendicular walls) of the casting die by model liquids of various density and viscosity are presented in the paper. Influence of localisation of the inlet system and inlet velocity on the flow character of model liquids of different viscosity in the system of a cold-chamber casting die was tested. Calculations performed by means of the calculation module NOVACAST (NOVAFLOW&SOLID) for the selected models of cavities cast by the pressure method are also presented in the paper.

You might also be interested in these eBooks

Control Engineering in Materials Processing II

View Preview

Info:

Periodical:

Solid State Phenomena (Volume 208)

Pages:

52-62

DOI:

https://doi.org/10.4028/www.scientific.net/SSP.208.52

Citation:

Cite this paper

Online since:

September 2013

Authors:

Rafał Dańko, Jerzy Stojek

Keywords:

Computer Simulation, Diecasting, Laminar Flow, Model Testing, Turbulent Flow

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] J. Dańko: Die-casting Machines – The base Theory, Design, Measurements, Operating. AGH publishers, Cracow, Poland 2000.

Google Scholar

[2] J.C. Lee, H. Kwang Seok, H.L. Lee: Influence of the gating geometry and the injection rate on the flow character of the aluminium alloy A356 in the state of its partial crystallization. Przegląd Odlewnictwa, vol. 54, 2004, No. 2, p.152

Google Scholar

[3] L.W. Garber: Theoretical Analisis and Experimental Observation of Air Entrapment During Cold Chamber Filling. Die Casting Engineer, p.14 – 22 (May – Jun 1982).

Google Scholar

[4] M.C. Thome, J.R. Brevick: Modeling Fluid Flow in Horizontal Cold Chamber Diecasting Shot Sleeves. The Ohio State University. ERC/NSM-C-93-122 (1993).

Google Scholar

[5] Y. Karni: Selection of Process Variables for Die Casting. The Ohio State University. ERC/NSM-C-91-08 (1991).

Google Scholar

[6] P. Madsen, I. A. Svendsen: Turbulent Bores and Hydraulic Jumps. J. of Fluid Mechanics, vol 129 (1983).

DOI: 10.1017/s0022112083000622

Google Scholar

[7] T. C.Tszeng, Y. L. Chu: A Study of Wave Formation in shot sleeve of Die Casting Machine. The Ohio State University. ERC/NSM-C-92-01 (Feb 1992).

Google Scholar

[8] J. Stojek: Control system of the first phase of die-casting process. PhD Thesis, AGH University of Science and Technology, Cracow, Poland 2002.

Google Scholar

[9] J. Dańko, R. Dańko, J. Stojek: Cognisable effects of model investigations of die casting processe. Archives of Foundry Engineering. 2008 vol. 8 spec. iss. 1 s. 57–62.

DOI: 10.1515/afe-2015-0072

Google Scholar

[10] J. Dańko, R.Dańko, J. Stojek: Model testing of casting process in cold-chamber die casting machine. Archives of Metallurgy and Materials. 2007 vol. 52 iss. 3 s. 503–513.

DOI: 10.1515/afe-2015-0072

Google Scholar

[11] Z. Jędrzykiewicz, J. Pluta, J. Stojek: Laboratory station for modeling fluid flow in chamber diecasting shot sleeves. Hydraulika i Pneumatyka, No. 1/1999.

Google Scholar

[12] Research project MSWiS nr 3 T08B 025 28 (in Polish)

Google Scholar