The Influence of Molding Parameters on the Structure of the ZnAl40Cu2Ti Alloy

Tomasz Mikuszewski; Rafał Michalik

doi:10.4028/www.scientific.net/SSP.246.235

Paper Titles

The Impact of the Heat Transfer Coefficient on High-Temperature Distributions in Steam Valve
p.217

The Deformability of Fe-Ni Superalloy during High Temperature Deformation
p.221

The Influence of the Components of the Bimetallic Tubes for the Way of Deforming in the Hollow Drawing Process
p.225

Structure and Properties of Steel Welding after Micro-Jet Cooling Process
p.231

The Influence of Molding Parameters on the Structure of the ZnAl40Cu2Ti Alloy
p.235

Forming Construction Elements for Aviation from Light Alloys with the Use of Cold Extrusion in Complex State of Strain
p.240

Causes of Increased Number of Non-Metallic Inclusions in Filtered Steel
p.244

Importance of Electrodes Slipping Algorithm for the Ferrosilicon Smelting Process
p.248

The Influence of Thermodynamic Conditions for Steel Filtration Efficiency
p.252

HomeSolid State PhenomenaSolid State Phenomena Vol. 246The Influence of Molding Parameters on the...

The Influence of Molding Parameters on the Structure of the ZnAl40Cu2Ti Alloy

Abstract:

The aim of this study was to determine the influence of casting technology on the structure of the ZnAl40Cu2Ti alloy. The scope of the examination included Brinell hardness tests and tests on optical microscopy, scanning electronic microscope test and X-ray microanalysis. The tests showed that, depending on the casting technology can be obtained different ZnAl40Cu2Ti alloy structure, characterized by different chemical composition in microareas. It has been pointed out that in order to get ZnAl40Cu2Ti alloy modification of Zn-Al-Cu alloy used technology casting is necessary.

You might also be interested in these eBooks

Technologies and Properties of Modern Utility Materials XXIII

View Preview

Info:

Periodical:

Solid State Phenomena (Volume 246)

Pages:

235-239

DOI:

https://doi.org/10.4028/www.scientific.net/SSP.246.235

Citation:

Cite this paper

Online since:

February 2016

Authors:

Tomasz Mikuszewski*, Rafał Michalik

Keywords:

Molding, Structure, Zn-Al Alloys

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] T. Savaskan, G. Purcek, P. Hekimoglu, Effect Of Copper Content On The Mechanical And Tribological Properties Of ZnAl27-Based Alloys, Tribol. Lett. 15/3 (2004) 257 – 263.

Google Scholar

[2] B. Prasad, Effect of microstructure on the sliding wear performance of a Zn-Al-Ni alloy, Wear 240 (2000) 100-112.

DOI: 10.1016/s0043-1648(00)00369-0

Google Scholar

[3] H. Kania, The structure of coatings obtained in the Zn-31Al-3Mg bath by the batch hot dip method. IOP Conf. Series: Mater. Sci. Eng. 35, 012003, (2012).

DOI: 10.1088/1757-899x/35/1/012003

Google Scholar

[4] H. Kania, The Structure of Coatings Obtained in the Zn-31Al-3Mg Bath on High-Silicon Steel, Solid State Phenom. 212 (2014) 101-106.

DOI: 10.4028/www.scientific.net/ssp.212.101

Google Scholar

[5] J. Mendala, Influence of the cooling method on the structure of 55AlZn coatings, IOP Conference Series - Mater. Sci. Eng. 22, 012004, (2011).

DOI: 10.1088/1757-899x/22/1/012004

Google Scholar

[6] J. Mendala, The influence of Si addition in 55AlZn bath on the coating structures obtained in the batch hot-dip metallization, IOP Conference Series - Mater. Sci. Eng. 22, 012005, (2011).

DOI: 10.1088/1757-899x/22/1/012005

Google Scholar