Studying Temperature Variations that Occurred during Cold and Hot Rolling of AA5454-O Alloy

Abstract:

In this study, temperature distribution that occurred during cold and hot rolling of AA5454-O alloy has been investigated. Temperature variation taking place in the aluminium alloy that has undergone plastic deformation between the rollers during hot and cold rolling process is of major importance in terms of determining the positive and negative characteristics or features which such temperature variation adds to the formation of the internal structure of the material concerned. Temperature distribution has been measured by use of the installed laboratory equipment and respective data recorded has been presented in the form of graphic charts. Temperature distribution has varied depending on the application of hot or cold rolling process and it has been noted that variations in terms of temperature reduction took place depending on the number of roll passes. While average temperature variation has occurred as a 16°C increase in the case of cold rolling, it has been observed that such variation appeared as a 100°C decrease on the average in the case of hot rolling.

• Periodical: Solid State Phenomena (Volume 267)
• Pages: 45-51
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.267.45
• Online since: October 2017
• Authors: Sinan Sezek*, Bunyamin Aksakal
• Keywords: Rolling , Cold Rolling, Hot Rolling, Metal Forming, Temperature Distribution

References

[1] E.N. Dvorkin, M.B. Goldschmit, M.A. Cavaliere, P.M. Amenta, O. Marini, W. Stroppiana, 2D finite element parametric studies of the flat-rolling process, J. Mater. Process. Tech. 68(1) (1997) 99-107.

DOI: 10.1016/s0924-0136(96)00027-1

[2] S. Serajzadeh, Prediction of microstructural changes during hot rod rolling, Int. J. Mach. Tools Manufac. 43(14) (2003) 1487-1495.

DOI: 10.1016/s0890-6955(03)00167-6

[3] A.F.M. Arif, O. Khan, A.K. Sheikh, Roll deformation and stress distribution under thermo-mechanical loading in cold rolling, J. Mater. Process. Tech. 147(2) (2004) 255-267.

DOI: 10.1016/j.jmatprotec.2004.01.005

[4] J.G. Lenard, The effect of roll roughness on the rolling parameters during cold rolling of an aluminum alloy, J. Mater. Process. Tech. 152(2) (2004) 144-153.

DOI: 10.1016/j.jmatprotec.2004.03.026

[5] O. Engler, X.W. Kong, K. Lücke, Recrystallisation textures of particle-containing Al–Cu and Al–Mn single crystals, Acta Materialia. 49(10) (2001) 1701-1715.

DOI: 10.1016/s1359-6454(01)00087-8

[6] A. Krishnaiah, U. Chakkingal, P. Venugopal, Production of ultrafine grain sizes in aluminium sheets by severe plastic deformation using the technique of groove pressing, Scripta Materialia. 52(12) (2005) 1229-1233.

DOI: 10.1016/j.scriptamat.2005.03.001

[7] A. Goloborodko, O. Sitdikov, R. Kaibyshev, H. Miura, T. Sakai, Effect of pressing temperature on fine-grained structure formation in 7475 aluminum alloy during ECAP, Materials Science and Engineering: A. 381(1-2) (2004) 121-128.

DOI: 10.1016/j.msea.2004.04.049

[8] Y. Harada, M. Ohmori, S. Maki, K. Mori, Sandwich-rolling of sintered chromium, J. Mater. Process. Tech. 143–144 (2003) 710-715.

DOI: 10.1016/s0924-0136(03)00358-3

[9] N. Stanford, D. Dunne, M. Ferry, Deformation and annealing of (011)[011̄] oriented Al single crystals, Acta Materialia. 51(3) (2003) 665-676.

DOI: 10.1016/s1359-6454(02)00445-7

[10] N. Stanford, D. Dunne, M. Ferry, Effect of orientation stability on recrystallization textures of deformed aluminium single crystals, Materials Science and Engineering: A. 348(1-2) (2003) 154-162.

DOI: 10.1016/s0921-5093(02)00748-7

[11] A. Said, J.G. Lenard, A.R. Ragab, M.A. Elkhier, The temperature, roll force and roll torque during hot bar rolling, J. Mater. Process. Tech. 88(1-3) (1999) 147-153.

DOI: 10.1016/s0924-0136(98)00391-4

[12] M. Kazeminezhad, A.K. Taheri, An experimental investigation on the deformation behavior during wire flat rolling process, J. Mater. Process. Tech. 160(3) (2005) 313-320.

DOI: 10.1016/j.jmatprotec.2004.06.020