Search results

At 22.5°, carbon-bamboo fiber showed the highest deformation among all materials, while both hemp and carbon fiber maintained comparatively lower values.
Mechanics of Composite Materials 2024;60:211–26. https://doi.org/10.1007/s11029-024-10185-3
Mechanics of Advanced Materials and Structures 2025. https://doi.org/10.1080/15376494.2025.2466220
Journal of Natural Fibers 2023;20. https://doi.org/10.1080/15440478.2022.2157921
Acta Phys Pol A, vol. 132, Polish Academy of Sciences; 2017, p. 879–82. https://doi.org/10.12693/APhysPolA.132.879

Introduction At present, there is increasing emphasis on sustainable construction, the use of waste materials and the recycling of construction waste.
Reiterman, Ecological Concrete Based on Blast-Furnace Cement with Incorporated Coarse Recycled Concrete Aggregate and Fly Ash Addition, Journal of Renewable Materials 5 (2017) 53-61
Reiterman, Fiber Reinforced Fly Ash Concrete and Extreme Fires, Key Engineering Materials 722 (2017) 12-17
Abbas, Effect of High Temperature on High-Volume Fly Ash Concrete, Arabian Journal for Science and Engineering, 2013, Volume 38, Number 6, Page 1369, https://doi.org/10.1007/s13369-013-0606-1 [8] Arabi N.S.
Brabec, The effect of elevated temperatures and nuclear radiation on the properties of biological shielding concrete, Key Engineering Materials 677 (2016) 8-16

Monte-Carlo method is base on computer science and suitable for some complex problems.
Distribution parameter of strength of the pipeline Strength r is the limit yield of the material, the average count is , the standard deviation is obtained by the statistic of the capability of the material.
Journal of Shenyang Jianzhu University(Natural Science), Vol.23(2007) p.204 [4] SH Dai and MO Wang, Reliability and the use of reliability in chemical equipment (Chemical industry publish, China 1987) [5] Wenqiang Luo, Yu Gong, Runyan Yang.
Earth science-Journal of China university of geosciences, Vol.23(1998)p.639 [6] Yifei Zhang, Yongxin Wang, Xintang Wang.
Journal of Basic Science and Engineering, Vol.17(2009) p.138

Journal of Applied Physics 117(11): 115703
Nature materials 5.5 (2006): 383-387
"Disorder-induced localization in crystalline phase-change materials."
Nature materials 10.3 (2011): 202-208
ACS applied materials & interfaces 6, no. 16 (2014): 14207-14214

Filice et al: Journal of Materials Processing Technology Vol. 191(2007), p. 92-95
Szekeres et al: Journal of Materials Processing Technology Vol. 189(2007), p. 65-72
Giardini et al: Journal of Materials Processing Technology Vol. 197(2008), p. 59-67
Attanasio: Journal of Materials Processing Technology Vol. 152(2004), p. 176-84
Bay: Key Engineering Materials Vol. 344(2007), p. 583-590

This view is based on the stress control fatigue properties of materials.
But when stress levels are close to the yield strength of materials, cyclic softening properties of some materials will significantly reduce the lives of mechanical elements, especially under the symmetric cycle loads.
So it is necessary to take into account of the material cyclic yield properties, which are defined as the fatigue properties of materials under the stresses close to the yield strength of materials.
Advanced Materials Research, Vol. 305 (2011), pp. 181-185
Weapon Material Science and Engineering, Vol. 19(1996), pp. 20-24.

Oohazama, Y.Sakaguchi, Novel network morphology of poly(p-oxybenzoyl), Journal of Polymer Science Part A: Polymer Chemistry. 43 (2005) 1624-1634
Chaowei, Fabrication and properties of a lubrication composite coating based on poly(p-hydroxybenzoic acid) (PHBA), Journal of Materials Science. 44 (2009) 227-233
Wang, Properties of POB reinforced PTFE-based friction material for ultrasonic motors, Journal of Polymer Engineering. 37 (2017)
Kim, Carbon Nanotube-Reinforced Thermotropic Liquid Crystal Polymer Nanocomposites, Materials. 2 (2009) 1955-1974
Kutz, Handbook of Environmental Degradation of Materials, Elsevier, Cambridge, 2018.

The characteristic physical properties of titanium alloy materials of the electrical discharge machining (EDM) small hole is studied theoretically and experimentally.
Thereby, the main characteristic of EDM is described as follow: it can machining whatever conductive materials and not be restricted by its hardness; it can machining blind-hole; deep-hole; slant-hole and profiled hole on the slant; it has low cutting force in machining process and requires low strength and stiffness.
Jahanmir: Journal of Tribology ASME Vol.123 (2001), p. 101–107 [2] E.
Key Engineering Materials, Vols. 375-376 (2008), p. 449-453
International Journal of Machine Tools & Manufacture, Vol.44 (2004), p.629-636

It also was supported by Shanxi Province Science Foundation for Youths (2010021021-2).
Journal of Marine Science and Application Vol. 7(1) (2008), p. 15 [2] Ding Xiaohong and Li Guojie: Topology Design Optimization of Rib Layout in Box Structure.
Journal Advanced Materials Research Vol. 97-101(2010), p. 3531 [3] Wang Dongfang, He Pengfei, Zhu Xiaoling and Liu Zishun: Interior Noise Control and Acoustic Optimization of Laminated Composite Box Structures.
Journal Shock and Vibration Vol. 11(3) (2004), p. 271 [5] P.
Journal Shock and Vibration Vol.2010, 17(1), p. 21 [6] G.

Controllable Preparation of Zinc Phosphate Materials with Different Morphologies and Particle Size Jiang-Jie Wang2, Xiao-Hong Yang2,*, Jing Wang1, Qin Tong1, Jin-Ku Liu1,* 1Department of Chemistry, East China University of Science and Technology, Shanghai 200237, P.
Zinc phosphate materials which have different morphologies, particle size and good crystalline were prepared via an effective template method.
Some practical experimental conclusions could be obtained, which were expected to have potential values in synthesis of functional materials.
The zinc phosphates [Zn3(PO4)2·4H2O] as an important inorganic functional materials with excellent thermal stability, colorless, non-toxic, good anticorrosive property, have been found widely applied to ion exchange materials, chelating agents, glass ceramics, high quality fertilizers, biomedical cements and especially as corrosion-resistant coatings[3,4].
Hong: Journal of Hazardous Materials, Vol. 270(2014), p.71.