Search results

Then the model was used to study the creep damage development of a four-material notched specimen of the welded joints which includes: base materials, coarse-grained HAZ, fine-grained HAZ (type IV), and weld materials. 2.
Table1.Creep properties of materials at T=630 o C Table2.Creep damage properties of materials at T=630 o C 3.1 Uniaxial problem: The application of our creep damage constitutive model to a uniaxial stress situation is firstly discussed.
Andersson: Computational Materials Science, Vol. 25 (2002), p. 34-41 [5] A.C.F.
Ashby: Metal Science, August-September (1980), p. 395 [6] A.
Ashby: Progress in Materials Science, Vol. 27(1982), p.189-244 [7] Patrick Onck and Erik van der Giessen: Journal of the mechanics and physics of solids, Vol. 47(1999), p. 99-139 [8] Nonaka et. al.: JSMS, Vol.35 No. 390 (1986), p. 299-304 (in Japanese) [9] A.

In this case, selected resources are Raw materials, Auxiliary materials, Water, Electric energy and Thermal energy.
Quantity Quality Mitigation & Restoration Duration Increase in materials consumption >X% with respect to mean value Increase in non-renewable and or non-recyclable materials consumption No mitigation is possible Long duration Auxiliary materials Failure increases the quantity of auxiliary materials needed with respect to standard condition?
Materials and Design Vol. 27 (2006), pp. 74-78
Safety Science Vol. 28 (1998), pp. 21-44
Journal of Hazardous Materials Vol.71 (2000), pp. 481-501

The results show that SPR joining dissimilar materials of steel and aluminum alloy is feasible and riveting joints take on high mechanical behavior.
Aluminum and steel are the most important construction materials for automotive structures.
The materials used for this test are 1.2mm 2A12 aluminum and 1.5mm DC01 cold-roll steel.
Acknowledgements The work reported herein was supported by National Natural Science Foundation of China (Grant No. 50665002), Natural Science Foundation of Jiangxi Province (Grant No. 2007GZC0869), Young Scientist Plan of Jiangxi Province, and Key Laboratory of Ministry of Education for Conveyance and Equipment (East China Jiaotong University).
References [1] X.Sun and M.A.Khaleel: International Journal of Impact Engineering Vol. 34(2007), p. 1668 [2] R.Porcaro, A.G.Hanssen, M.Langseth and A.Aalberg: Journal of Materials Processing Technology Vol.171 (2006), p 10 [3] R.J.Liu, S.W.Yu, C.J,Zhu and Y.C,Wang: Transaction of Beihua University Vol.8(2007),P. 369(In Chinese) [4] X.M.Chen, Z.C.Huang, S,W,Kang: S.W.Kang: Transaction of East-China Jiao-Tong University Vol. 25(2008), p. 106(In Chinese) [5] X.Sun, E.V.Stephens, and M.A.Khaleel: International Journal of Fatigue Vol. 29 (2007),P. 370

Journal of materials science, 53(7):4709-4733
Journal of materials science, pp. 3099-3106
IPTEK: The Journal for Technology and Science, 22(1), pp. 24-28
Materials and Structures, 55(1), p.22
On the development of fly ash-based geopolymer concrete, ACI Materials Journal, 101, 467-472

The delamination is a major problem associated with the drilling of fiber reinforced composite materials.
Journal of material science.
Journal of material processing Technology.
Journal of Material Processing Technology.
Journal of Material Processing Technology.

Shows the tensile strength of the cast specimens using different chill materials.
Journal of materials science, vol-33 pp. 23 -28
“Metal Matrix Composites: Production by the Stir Casting Method”, Journal of Material Processing and Technology, 92, pp.17
“Effect of cooling rate on eutectic cell count, grain size, microstructure and ultimate tensile strength of hypoeutectic cast iron”, Journal of materials Engineering and performance, volume8(4),pp. 417-423
Standard test method for tension testing of metallic materials.

As the development of science and technology, the requirement of modern industry to metal materials are higher and higher nowadays.
References [1] Zhang Jiang, Li Zongquan, Materials Science and Engineering. 4(2001) 122-124(in Chinese)
[5] Meng Fei, Pei Yanbin, Guo Shiju, Powder Metallurgical Materials Science and Engineering. 1(2005) 55-56(in Chinese)
[14] Li Jianlin, Jiang Dongliang, Tan Shoutao, Journal of Inorganic Materials. 2(2000) 336-340 (in Chinese)
[16] Yu Qiang, Li Yubao, Wei Binqing, Liang Ji, Wu Dehai, Journal of Tsinghua University(Science and Technology). 4(1999) 25-27(in Chinese)

Abstract: Titanium is difficult-to-cut materials due to its poor machinability and thermal conductivity when machining at high cutting speed.
Transaction ASME Journal of Engineering Industry, (1991), 113, 160-168
Analytical stability prediction and design of variable pitch cutter, Journal of Manufacturing Science and Engineering, Transaction of the ASME 121 (1999) 173
An analyical design method for milling cutter with non-constant pitch to increase stability, part 1: theory and part 2: application, Journal of Manufacturing Science and Engineering 125(2003) 29-38
Journal of Sound and Vibration, (2008), 317(3-5), 664-686

The aim of this study is to find out the mechanical properties and tensile and impact strength of items produced by using three different commercially available materials; two WPC materials containing wood flour, and pure polylactic acid (PLA) as reference material.
Materials and Methods The reference material was PLA PrintPlus 1.75 mm Natural filament supplied by 3Dfactories.
The wood-filled materials showed weaker performance.
The printed specimen also appeared more flexible compared to the two other materials used.
Wright, Anisotropic material properties of fused deposition modeling ABS, Rapid Prototyping Journal. 8 (2002) 248-257

International Journal of Rock Mechanics and Mining Sciences, 1998, 35(1): 75－84
A physical model study of jointed rock mass strength under uniaxial compressive loading[J].International Journal of Rock Mechanics and Mining Sciences, 1997, 34(3－4): 165.e1－165.e15
Strength predictions for jointed rocks in confined and unconfined states[J].International Journal of Rock Mechanics and Mining Sciences,1994, 31(1): 9-22
International Journal of Rock Mechanics and Mining Sciences, 2010, 47: 568－82
Influence of the geometry of partially-spanning joints on the uniaxial compressive strength of rock[J].International Journal of Rock Mechanics and Mining Sciences,2012,50: 140－146.