Search results

Zhang1,b 1 School of Naval Architecture, Ocean and Civil Engineering, Shanghai JiaoTong University, Shanghai 200240, P.
Introduction The laser forming process originally was developed and used by Masubuchi [1] and Namba [2] firstly.
Its chemical composition is listed in Table 1 and the thickness is 0.7 mm.
The specimens tested in uniaxial tension are prepared according to ISO6892 with the gauge length 50 mm after line-heating (in Fig.1).
Rare Metal Materials and Engineering, 2007 (36): 475-479

In phase 1(0-3MPa), the strength increases linearly with the increase of confining pressure.
References [1] B.
Permafrost, Edmonton, Vol. 1, 671-674 (1978)
Berlin: Springer Verlag, p, 1-15 (1980)
Kluwer Academic Publ., Boston, 479-488 (2001).

The chemical structures of CY, TCs and SAs were shown in Fig. 1.
The MRM setting was shown in Table 1.
Table 1 showed the optimized MRM parameters.
References [1] Kümmerer K.
Vol. 89 Suppl. 1 (1999) p.9-67

Aeroacoustics Investigation of an Automotive Exhaust Muffler Fabrício Torres Borghi 1, a, José Eduardo Mautone Barros 1, b, Ramon Molina Valle 1, c. 1 Federal University of Minas Gerais – Mechanical Engineering Department Avenida Antônio Carlos, 6627, Belo Horizonte - MG - Brazil - Cep.:31270-901.
Results The comparison between the experimentally measured data and the CAA prediction is showed for a probe point by Figure 1.
Fig.ure 1.
References [1] A.
Journal of Sound and Vibration 1983;90(4):479±90

Traditional mineral fuels such as diesel oil have long been a blend of several tens of constituents to which currently vegetable fuel is increasingly added (up to 7% in Poland) [1].
Fig. 1.
This classifier is similar to that shown in Fig. 1, as it has the same input variables (minimum and maximum values of pressure in the cylinder and in the injection pipe).
References [1] L. 
Yoon et al., A method for combustion phasing control using cylinder pressure measurement in a CRDI diesel engine, Mechatronics (2007) 469-479

A schematic view of the experimental setup is depicted in Figure 1.
The modulation frequencies (typically below 1 Hz) are considerably lower than the magnetic field frequency of 50 Hz.
Fig.1: The used electromagnetic casting apparatus.
References [1] B.S.
Sci, 361(2003) 479–95

Introduction Bone tissue possesses the hierarchical architecture at various scale-levels (Fig. 1), resulting in exerting some bio-functions because each hierarchy system strongly relates to each other, e.g. the toughness mechanism of bone [1].
Since BAp crystallizes in an anisotropic hexagonal crystal as shown in Fig. 1, mechanical properties of a BAp crystallite depend on the crystal orientation.
Fig. 1 Hierarchical bony structure and the dominant constituents of collagen (Col) and biological apatite (BAp).
References [1] P.
Umakoshi, Unique alignment and texture of biological apatite crystallites in typical calcified tissues analyzed by microbeam x-ray diffractometer system, Bone 31 (2002) 479-487

Fig. 1 shows the X-ray diffraction patterns of Ti-Al-Si-C-N coatings with various Si contents.
In order to investigate a shift of the XRD peak positions of Ti-Al-Si-C-N coatings, the d200 values were obtained from the results of Fig. 1.
Fig. 1.
References [1] GwangSeok Kim, SangYul Lee, JunHee Hahn, Surf.
Rajam, Vacuum 81 (2006) 479

Fig.1.
Fig. 1 shows a block diagram of the system which assists group conversation using only one Kinect sensor.
Experiments In the experiment, 7 subjects (1 female and 6 male, their age range is 21-25 years old) were recruited.
References [1] M.
Physil Rev 89: 453-479, American Physiological Society (2009)

MS is often progressive and disabling [1].
The studies process is presented in Fig. 1.
Characteristics of patients and healthy subjects are presented in Table 1.
Table 1.
Gait Posture2011; 479-484.