Search results

Torre1,5,a 1 European Lab. for Non-Linear Spectroscopy (LENS), Università di Firenze, via Carrara 1, I-50019 Sesto Fiorentino, Italy. 2 Istituto Nazionale di Ottica (INO) - CNR, Largo E.
PU2-MoS2 PU1-MoS2 Figure 1.
In both samples, the concentration of nanoparticles was less than 1 wt-%.
References [1] T.
Self-assembly of subnanometer-diameter single-wall MoS2 Nanotubes, Science, Vol. 292, 2001, pp. 479-481

The chemical compositions and physical properties of slag are given in table 1.
References [1] Erhan guneyisi, Mehmet Gesoglu.
Materials and Structures, 2008, (41) : 479-493
Pozzolanic and cementitious by products as mineral admixtures for concrete-a critical review, vol. 1.
Pozzolanic and cementitious by products in concretes-another look, vol. 1.

The numerical analysis for the turbulence in the 180°bend tube was taken by Patankar etc. [1].
Obviously, when is large, coefficient , and close to 1.
The mesh was shown as Fig.1.
References [1] Patankar, S.V.
TABAKOFF: Journal of Aircraft, Vol.12 (1975) , pp. 471-479

Zhang1,b 1 School of Naval Architecture, Ocean and Civil Engineering, Shanghai JiaoTong University, Shanghai 200240, P.
Introduction The laser forming process originally was developed and used by Masubuchi [1] and Namba [2] firstly.
Its chemical composition is listed in Table 1 and the thickness is 0.7 mm.
The specimens tested in uniaxial tension are prepared according to ISO6892 with the gauge length 50 mm after line-heating (in Fig.1).
Rare Metal Materials and Engineering, 2007 (36): 475-479

In phase 1(0-3MPa), the strength increases linearly with the increase of confining pressure.
References [1] B.
Permafrost, Edmonton, Vol. 1, 671-674 (1978)
Berlin: Springer Verlag, p, 1-15 (1980)
Kluwer Academic Publ., Boston, 479-488 (2001).

The chemical structures of CY, TCs and SAs were shown in Fig. 1.
The MRM setting was shown in Table 1.
Table 1 showed the optimized MRM parameters.
References [1] Kümmerer K.
Vol. 89 Suppl. 1 (1999) p.9-67

Traditional mineral fuels such as diesel oil have long been a blend of several tens of constituents to which currently vegetable fuel is increasingly added (up to 7% in Poland) [1].
Fig. 1.
This classifier is similar to that shown in Fig. 1, as it has the same input variables (minimum and maximum values of pressure in the cylinder and in the injection pipe).
References [1] L. 
Yoon et al., A method for combustion phasing control using cylinder pressure measurement in a CRDI diesel engine, Mechatronics (2007) 469-479

Aeroacoustics Investigation of an Automotive Exhaust Muffler Fabrício Torres Borghi 1, a, José Eduardo Mautone Barros 1, b, Ramon Molina Valle 1, c. 1 Federal University of Minas Gerais – Mechanical Engineering Department Avenida Antônio Carlos, 6627, Belo Horizonte - MG - Brazil - Cep.:31270-901.
Results The comparison between the experimentally measured data and the CAA prediction is showed for a probe point by Figure 1.
Fig.ure 1.
References [1] A.
Journal of Sound and Vibration 1983;90(4):479±90

A schematic view of the experimental setup is depicted in Figure 1.
The modulation frequencies (typically below 1 Hz) are considerably lower than the magnetic field frequency of 50 Hz.
Fig.1: The used electromagnetic casting apparatus.
References [1] B.S.
Sci, 361(2003) 479–95

Introduction Bone tissue possesses the hierarchical architecture at various scale-levels (Fig. 1), resulting in exerting some bio-functions because each hierarchy system strongly relates to each other, e.g. the toughness mechanism of bone [1].
Since BAp crystallizes in an anisotropic hexagonal crystal as shown in Fig. 1, mechanical properties of a BAp crystallite depend on the crystal orientation.
Fig. 1 Hierarchical bony structure and the dominant constituents of collagen (Col) and biological apatite (BAp).
References [1] P.
Umakoshi, Unique alignment and texture of biological apatite crystallites in typical calcified tissues analyzed by microbeam x-ray diffractometer system, Bone 31 (2002) 479-487