Search results

The presence of surface impurities and the large amount of hydroxyl groups make plant fibers less attractive for polymeric materials reinforcement.
Due to increase in population, natural resources are being exploited substantially as an alternative to synthetic materials.
Method Materials Agel leaf fibers (ALF) were obtained from cultivation area in Banyuwangi, East Java, Indonesia.
Material Science 34:7 (2011) 1575–1581
Setyono, A preliminary study: the influence of alkali treatment on physical and mechanical properties of coir fiber, Journal of Materials Science Research 2:4 (2013) 80-88.

Preparation of Water-resistant Electrode Coating with Palmitic Acid by Microwave Reaction Chen Wenjun1, a, Gui Chibin2 and Sun Ji1 1College of Naval Architecture and Power,Naval University of Engineering,Wuhan 430033,China 2College of Materials Science and Engineering, Huazhong University of Science and Technology,Wuhan 430074,China achenwenjun83@163.com Keywords: Palmitic acid; Microwave reaction; Water-resistant coating; Diffusible hydrogen Abstract.
Fig.1 shows that when the electrodes removed from the petroleum ether solution, the palmitic acid did not react with the electrode surface material, but in a free state.
Plisko:Journal of Applied Spectroscopy, Vol. 67 (2000) No.6, p.769
Patil , Tsuneharu Mukaiyama and Animesh Kumar Rakshit: Journal of Surfactants and Detergents,Vol.7 (2004) No.1,p.87
Berchiesi: Journal of Thermal Analysis, Vol. 13 (1978),p.105

Journal of Achievements in Materials and Manufacturing Engineering.
Kennedy: Laser Cladding of Aerospace Materials.
Journal of Materials Processing Techology.
Journal of Mechanical Science and Technology.
Landkof: Laser Surface Melting of AISI 4340 Steel, Materials Science and Technology.

It containes a lot of carbohydrate, protein, soybean oligosaccharide, soybean isoflavone, soybean saponin and other functional materials [1,2], Treatment of soybean whey effluent has always been a difficult problem faced by soybean protein isolate enterprises.
This topic uses soybean whey effluent to make a study of new soybean whey drinks, which can not only make the full use of the functional materials from the wastewater, but also achieve the effect of the wastewater treatment.
According to fig.4,Compared with raw materials, milk, soybean milk powder and soybean food, activity of trypsin inhibitor in soybean whey was the lowest, which was in line with the standard for drinking.
Reference [1].Pouliot Y,Wijers M C,Gauthier S E,et al.Fractionation of whey protein hydrolysates using charged UF/NF membranes[J].Journal of Membrane Science,1999,158(1/2):105-114
A composite protein beverage development and some technical parameter [J].journal of shenyang agriculture college journal, 1998,29(1):44-46.

Introduction Structural reliability of composite materials can be strongly affected by the fracture properties of the interface between fiber and matrix [1,2].
The load-bearing capacity of composite materials depends on the efficiency of stress transfer at the bonded and debonded interfaces, which are mainly controlled by the mechanical properties of fiber and matrix and by the nature of the bonding.
Materials and Structures, Vol. 42 (2009), p765
Journal of Zhejiang University, 6A (Suppl.
Journal of American Ceramic Society, Vol. 78 (1995), p560

It is different from the low-end products with health risks burned by chemical materials on the market.
Journal of Archaeological Science. 78(2017)112-119
Key Engineering Materials.798(2019)242-247
Journal of African Earth Sciences. 84(2013)13–19
Applied Clay Science.31(1-2)(2006)1–15

Two materials and 6 types of specimens were subjected to blast loading.
Construction and Building Materials 94: 536-546
Construction and Building Materials 120: 54-64
Development of Ultra-High Performance Concrete Against Blasts: From Materials to Structures.
Inertial effect on concrete-like materials under dynamic direct tension.

Materials and Methodology The MES was performed by Dry Distillation (DD) and Wet Distillation (WD) at irradiation power of about 450 W and temperature about 100 oC for 1 hour whereas CEM was performed by Hydro Distillation (HD) and Steam Distillation (SD) at extraction power of 450 W and temperature 100 oC for 8 hours.
Spiro: Study of Microwave extraction of essential oil constituents from plant materials.
Journal of Microwave Power Electromagnetic Energy, Vol. 29 (1994), p. 231-241
Spiro: Study of Microwave Extraction of Essential Oil Constituents from Plant Materials, Journal of Microwave Power and Electromagnetic Energy, Vol. 29 (4) (1994), p. 231-241
Pare: Microwave-Assisted Extraction from Materials Containing Organic Matter, U.S.A Patent 5,458,897, (1995).

Moreover, research in the field of nanotechnologies has shown that textured materials and low surface energy can greatly reduce ice adhesion strength.
Depending on the type of materials, surface roughness can either promote the formation of air pockets within pores or between coating surface asperities (low adhesion strength) [2-8].
Paynter, Superhydrophobic properties of ultrahin rf-sputtered Teflon films coated etched aluminium surfaces, Materials Letters. 62 (2008) 1226-1229
Journal of adhesion science and technology, 25 (2011) 27-40
Farzaneh, Superhyrophobic surfaces prepared b RF-sputtered poytetrafluoroethyene coating, Journal of applied surface science, 257(2010) 1540-1543

(2) Materials at the rim of electrode bottom are removed first in Micro-EDM.
Rahman: Journal of materials processing technology.
Roehner: CIRP Journal of Manufacturing Science and Technology.
Lauwers: Journal of Materials Processing Technology.
Wang: Chinese Journal of Aeronautics.