Search results

After that, a lot of efforts have been made in this area, such as the research done by Palomo et al.[4,5], Davidovits [6,7] and van Deventer et al. [8-10].
Studies performed by Payá et al. [15] shows that independently from the origin of FCC, this byproduct presents an uniform composition.
“El techo que cubre el mundo: la teja de microconcreto” Ed.
“El techo que cubre el mundo: la teja de microconcreto” Ed.

The microstructure consists of fine Al crystal grains (grain size; around 200-500nm), and inter-metallic compounds.
We have developed a P/M Aluminum alloy with heat-resisting properties, Al -Si -TM -RE alloy [2].
Mg/m3) Al-12Si-1.2Ni -1Cu-1Mg Al-17Si-3.5（Fe、 Ni）-1.5Zr-5MM Chemical composition （mass%) JIS AC8A-T7 New PM-Al alloy 60 110 Fatigue strength at 523K （MPa） 170 230 U.T.S at 523K (MPa) 83.0 89.5 Young's module （GPa） 21.0 16.9 C.T.E （×10-6/K） 2.70 2.84 Density （Mg/m3) Al-12Si-1.2Ni -1Cu-1Mg Al-17Si-3.5（Fe、 Ni）-1.5Zr-5MM Chemical composition （mass%) JIS AC8A-T7 New PM-Al alloy Table .1 shows the properties of the powder forging sample which was made from this Al -Si -TM -RE alloy.
Properties of New PM-Al alloy Fig.9.
Tensile fracture surfaces of this P/M-Al materials

Battery cell components Chemical formulation Type of el.
Root cause Aging mode Main macroscopic effect Low neg. electrode potential SEI growth (by consuming lithium and solvent); T-activated, el.
-chemical R↑ ® Capacity↓, DLi,el↑ High pos. electrode potential Oxidation of electrolyte components; T activated, el.
Capacity↓ ® R↑, DLi,el↑ High discharge rate Particle (contact) cracking, hot spots; physical, chemical R↑, Capacity↓ High charge rate Lithium plating on (neg. electrode); el. chemical., chemical Capacity↓ ® R↑ SoC swing (DSoC) Mechanical disintegration from active particle to cell level; physical, el.
As one example Sarwar et al. investigated the combination of battery cells and supercapacitors in a passive system, and showed that such a combination is a promising solution for the very power demanding HEV [23].

High purity aluminum (99. 9 %), magnesium (99. 9 %) and zinc (99 %), and Al-Zr, Al-Cu, Al-Cr and Al-Yb alloys as raw materials were smelted into the alloys.
The spherical coherent dispersoids contain Yb, Zr and Al according to EDX analysis.
Gerard and E.L.
Zakharov, et al: Mater.
Fang，et al.

Ezz El-Din Hemdan et al [16] proposed a framework of seven pre-trained classifiers called COVIDX-Net and trained it with X-ray images for the automatic detection of COVID-19.
[7] Silva, Pedro, et al.
[16] Hemdan, Ezz El-Din, Marwa A.
Victor, et al.
[22] El Asnaoui, Khalid, and Youness Chawki.

Rajendran et al., [15] also reported that a high cross link density of glass network has Poisson ratio in order of 0.0-0.2, while a low cross link density glass network will have Poisson’s ratio between 0.3 and 0.5.
El-moneim, L.A.
El-latif, Ultrasonic studies on ternary TeO2 - V2O5 - Sm2O3 glasses, Materials Chemistry and Physics. 61 (1999) 103–109
El-Mallawany, E.
[12] A.A El-moneim, Acoustical and structural properties of 65SiO,-15PbO-5CaO-( 15-x)K,O-xNa,O glass system, Materials Chemistry and Physics. 52(97) (1998) 36–40

Microstructure and Mechanical Properties Change with Cold Rolling of New Ti-13Nb-1.5Ta-3Mo Alloy Adam Otabil1,a*, Mohamed El-Hofy2,b, Mohamed A.H.
Gepreel1,c* 1Materials Science and Engineering Department, Egypt-Japan University of Science and Technology, New Borg El-Arab City 21934, Alexandria, Egypt. 2Industrial and Manufacturing Engineering Department, Egypt-Japan University of Science and Technology, New Borg El-Arab City 21934, Alexandria, Egypt.
According to Min et al, “the combination of dislocation slips and {332} (113) twinning was helpful for the achievement of high strength and strong ductility in Ti-15Mo-5Zr and Ti-10Mo-2Fe alloys.
Mo(eq) = 1.00[Mo]+ 0.22[Ta]+ 0.28[Nb]+ 0.67[V] +1.60[Cr]+2.90[Fe] -1.00[Al] (1) Fig. 2 The Bo/Md map for Ti-13Nb-1.5Ta-3Mo indicating the strategic position highlighted in blue spot.

El-Mahllawy, A.
El Nagar, Production of geopolymer composites enhanced by nano-kaolin material, J.
EL Achouri, M.
Mustafa Al Bakri, H.
El-Naggar, M.

In the 1960s, Moe [11] and Hognestad & Elstner [8] conducted research, while more recent work has been performed by El-Salakawy [6] and Teng, Cheong & Kuang [12].
The most recent work has been undertaken by Borges, Melo, Gomes [3], and also by El-Shafiey, Hussein & Abdel-Aziz [5].
Eight slabs with symmetrically placed openings tested Augustin et al. [1] and [2].
The experiences from non-linear modelling of the flat slab specimens with openings by Augustin et al. [1] were utilized for the non-linear analyses.
El-Salakawy, M.

THERE ARE VARIOUS ADSORPTION ISOTHERMS, SUCH AS FREUNDLICH, LANGMUIR, HILL, KHAN, FLORY HUGGINS, EL-AWARDY, AND FRUMKIN.
Rocco, et al., Glycine max meal extracts as corrosion inhibitor for mild steel in sulphuric acid solution, Journal of Materials Research and Technology. (2020) 912756-12772
El-Azaly, Henna extract as green corrosion inhibitor for carbon steel in hydrochloric acid solution, Int.
Chen, et al., Papaya leaves extract as a novel eco-friendly corrosion inhibitor for Cu in H2SO4 medium, Journal of Colloid and Interface Science, 582 (2021) 918-931
El-morsi, M.