Search results

This is the mechanism of the material removal in ECMP.
Advanced Materials Research, Vol.314-316 (2011), p.2565 [4] Zhai W.J, Yang Y.Z.
Advanced Materials Research, Vol.239-242 (2011), p.920 [5] Hong Y, Devarapalli V.K, Roy D, and Babu S.V.
Journal of The Electrochemical Society, Vol.154 (2007), p.H444 [6] MATJAZ F, INGRID M.
Corrosion Science, Vol.52 (2010), p.2737

The materials could only densify up to 84-92% of theoretical density.
The concentration of aluminum powder in the starting materials ranged between 20 and 50 vol%.
Fukunaga, Highpressure sintering of cBN-TiN-Al composite for cutting tool application, Diamond and Related Materials, 11 (2002) 280. 2.
Zhao, Penetration and adhesion behaviour of boron nitride by liquid aluminum, Journal of Materials Science letters, 11 (1992), 199. 4.
Okada, Interfacial reaction wetting in the boron nitride/ molten aluminum system, Acta metallurgical materials, 41 (1993), 2963.

Journal of Alloys & Compounds, 2017, 692:301-312
Journal of Alloys & Compounds, 2017, 692:301-312
Materials Science Forum, 2014, 783-786:2491-2496
Materials Science and Engineering, 1979, 37(3):237-247
Journal of Materials Engineering and Performance, 1993, 2(5):745-758

Nanosized particles possess characteristic physical and chemical properties different from those of bulk materials due to the confinement of electrons, excitons, and photons into small volumes.
In the following measurements, 20nm and 5000nm Fe powders wrapped by the same insulating materials are measured at the same time.
Thus independent of materials wrapping Fe powders, we can compare the distinctions of heat transfer among Fe powders.
Xiao: International Journal of Heat and Mass Transfer Vol.48 (2005), p. 3932 [4] S.
Titov, International Journal of Heat and Mass Transfer Vol.46 (2003), p. 1103

Margin Geometry Substrate materials Square Epoxy (a) (b) (c) Acknowledgments The author gratefully acknowledges Prof.
Journal of Material Research 2000;15:676-682
Advanced Engineering Materials, 2000; 2: 745-748
Journal of Materials Research, 2001; 16: 1471-1477
Ceramic-based layer structures for biomechanical application, current opinion in solid state and material science.

Effect of Curing System on Mechanical Property of Slag- Based Geopolymer Qing Wang1, a, Xin Tu1,b , Zhaoyang Ding1,c, Zhitong Sui2,d 1School of Materials Science and Engineering ,Shenyang Jianzhu University, Shenyang,China 110168 2School of Materials & Metallurgy, Northeastern University , Shenyang, 110004, China.
In this paper, slag and metakaolin as source materials, mechanical property is studied by changing the curing system.
Material and Experiment Raw materials.
Study of Geopolymer Based on Kaolinite with Different Activation,Journal of Material Science and Engineering, 2004,22(4):550~553.
ACI Materials Journal,2004,11-12:467~472 [6]Wang Gang, Ma Hong-wen, Ren Yu-feng, Feng Wu-wei, Ding Qiu-xia.

In these theories, rock material and micro-cracks are together approximated as an equivalent continuous, homogeneous and anisotropic medium.
Acknowledgment The woke was financially supported by the National Natural Science Foundation of China (51109084), the Natural Science Foundation of the Fujian Province, China (2011J01317) and State Key Laboratory for GeoMechanics and Deep Underground Engineering, China University of Mining & Technology (SKLGDUEK1012) References [1] Morris WL, Buck O, Inman RV: Journal of Applied Physics. 50: 6737-6741(1979)
Reuschle: International Journal of Rock Mechanics and Mining Sciences.37:1019-1026(2000)
[32] Audrey Ougier-Simonin, Jerome Fortin, Yves Gueguen, Alexandre Schubnel, Frederic Bouyer: International Journal of Engineering Science. 49(1):105-121(2010)
[39] Green DH, Wang HF, Bonner BP: International Journal of Rock Mechanics and Mining Science and Geomechanics Abstracts, 30(7): 755-761(1993)

The advantage of incorporating materials combined with cells, is that the material matrix can provide the initial structural support required and retain cells in the defective area.
Mason, Hydrophilic-hydrophobic hydrogels for cartilage replacement, Journal of the Mechanical Behavior of Biomedical Materials 2 (2009) 588-595
Boyan, A review of polyvinyl alcohol and its uses in cartilage and orthopedic applications, Journal of Biomedical Materials Research Part B: Applied Biomaterials 100 (2012) 1451-1457
Filho, Rheological behavior of alginate solutions for biomanufacturing, Journal of Applied Polymer Science 113 (2009) 3866-3871
Adhikari, Biodegradable synthetic polymers for tissue engineering, European Cells and Materials 5 (2003) 1-16.

It is made by the C25 concrete and HRB335steel bar with the thickness of 35mm concrete cover, setting a settlement joint of each 12m .The structure is shown as in Fig.1 and the parameters of main materials are listed in Table1.
Table 1 The parameters of main materials Material Elastic modulus E(MPa) Poisson ratio μ Density ρ(kg/m3) Internal friction angleφ(°) Cohesion C(KPa) Reinforced Concrete 2.8×104 0.2 2500 Soil 50~300 0.3 1800 31 3.8 Fig. 1 Structural diagram of cantilever retaining wall Numerical Test Analysis The retaining wall and soil are both simulated by the element of SOLID45 in ANSYS, with the assumption of elastic materials.Due to the low strain dynamic response, the bottom of the model is fixed, with the displacement of X-direction constrained not only front but also back of the model.
(Urban Science Edition), 2009, 26(4): 1~4
AIAA Journal, 1999, 37(4): 513-515
Journal of Vibration and Shock, 2002, 21(4): 72~77

Eda TURAN, Tarık KOÇAL, The Online Journal of Science and Technology, vol. 1, no. 4, pp. 24–30, 2011
Sandeep Bhat, World Academy of Science, Engineering and Technology 61 2012, 2012
Murugan, Journal of Materials Processing Technology, vol. 176, no. 1–3, pp. 230–239, Jun. 2006
Yildiz, Materials & Design, vol. 28, no. 2, pp. 649–656, Jan. 2007
Yannacopoulos, Journal of Materials Processing Technology, vol. 212, no. 1, pp. 286–294, Jan. 2012