Search results

Ward: Journal of Materials Processing Technology Vol. 125-126 (2002), p. 619 [3] H.K.
Dowson: Journal of Materials Processing Technology Vol. 121(2002), p. 332 [5] H.
Sun: Journal of Materials Processing Technology Vol. 177 (2006), p. 634 [6] T.
Pillinger and P.Hartley: Journal of Materials Processing Technology Vol. 80-81(1998), p. 199 [7] H.
Takasu: Journal　of　Materials Processing Technology Vol. 125–126 (2002), p. 613

Acknowledgement This work was supported by the Natural Science Foundation of Shandong Province (ZR2014EMQ005, ZR2010EQ001), the Project of Shandong Province Higher Educational Science and Technology Program (Grant No.
Journal of Power Sources 206(2012)267–273
Journal of Power Sources 256(2014)32-36
High performance amorphous-Si/SiOx /C composite anode materials for Li-ion batteries derived from ball-milling and in situ carbonization.
Journal of Power Sources 256(2014)190-199

Materials and Methods The selection of materials for RT in injection molding has an impact on the injection molding process.
Therefore, high thermal conductivity is mandatory in mold materials.
Advantages and disadvantages of the techniques and materials analyzed.
Elangovan, “Mechanical behaviour of aluminum particulate epoxy composite–experimental study and numerical simulation,” International Journal of Mechanical and Materials Engineering, 7 (2012) 214–221
Verma, “Mechanical behaviour of copper and aluminium particles reinforced epoxy resin composites,” American J. of Materials Science, 5 (2015) 84–89

ZrO2 is bioinert materials and higher physical properties than hydroxyapatite [5].
Lameiras, “Synthesis and Characterization of Composite Powders of Partially Stabilized Zirconia and Hydroxyapatite”, Materials Characterization 45 (2000) 51-59
Naemchanthara, “Temperature Effect on Calcium Phosphate Synthesized from Chicken Eggshells and Ammonium Phosphate”, Journal of Applied Sciences 10 (2010) 3337-3342
Hohemberger, “Correlation between Thermal Treatment and Tetragonal/Monoclinic Nanostructured Zirconia Powder Obtained by Sol-Gel Process”, Advanced Materials Science, 17 (2008) 62-70
Kannan, “Synthesis and Sintering of Hydroxyapatite-Zirconia Composites”, Materials Science and Engineering, 20 (2002) 187-193

ACS Applied Energy Materials. 3(1), (2020) 66-98
Yuan, Sol-gel solvothermal route to synthesize anatase/brookite/rutile TiO2 nanocomposites with highly photocatalytic activity, Journal of Sol-Gel Science and Technology. 85(1-4), (2017) 1-8
Zhong, Controllable synthesis of brookite/anatase/rutile TiO2 nanocomposites and single-crystalline rutile nanorods array, Journal of Materials Chemistry. 22(16), (2012) 7937-7944
Kim, Sol-gel synthesis of mesoporous anatase-brookite and anatase-brookite-rutile TiO2 nanoparticles and their photocatalytic properties, Journal of Colloid and Interface Science. 442, (2015), 7 p
Gholami, Transition metal ions effect on the properties and photocatalytic activity of nanocrystalline TiO2 prepared in an ionic liquid, Journal of Hazardous Materials. 172(2-3), (2009) 1573-1578

Experimental Preparation of materials.
The materials utilized in the research include the extracted oil palm mesocarp from autoclave sterilization and industrial crude palm oil (CPO) from Sawit Raya Sdn.
Malaysian Journal of Analytical Science, 21(4). https:// doi.org/10.17576/mjas-2017-2104-21 [2] Ainie, K. (2004).
In Journal of Science and Technology
Materials Science Forum, 1048, 485–492. https://doi.org/ 10.4028/www.scientific.net/msf.1048.485 [22] Nokkaew, R., & Punsuvon, V. (2014).

Introduction Etching is a principle key process for removing materials from the sample surface.
RF Inductively coupled plasma (ICP) and Capacitive coupled plasma (CCP) sources have been used, widely, in the literature for dry etching of different materials.
Cuomo, Langmuir probe measurements of a radio frequency induction plasma, Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films. 11 (1993)152
Rhee, The effect of He or Ar/O2 plasma treatment on Si surface prior to chemical vapor deposition of SiO2, Journal of Materials Science: Materials in Electronics. 15(2004) 37
Rashed, analysis of cylindrical langmuir probe using experiment and different theories, Plasma physics report journal. 39 (2013) 1

Zeren, Journal of Manufacturing Science and Engineering of Transactions of the ASME, 128 (2006) 119-129
Pillinger, Journal of Manufacturing Science and Engineering of Transactions of the ASME, 123(2001) 397-404
John, Journal of Manufacturing Science and Engineering of Transactions of the ASME, 123(2001)57-65
Melkote, Journal of Manufacturing Science and Engineering, Transactions of the ASME, 127(2005) 75-83
Hu, Key Engineering Materials, 315-316(2006), 174-179

Daio: Journal of Crystal Growth Vol.210 (2000), p.36-39
Choi and et al: Materials Letters Vol.58 (2004), p.2091-2095
Moudgil: Journal of Colloid and Interface Science Vol.256 (2002), p.137-142
Fisher: International Journal of Machine Tools & Manufacture Vol.47 (2007), p.1-13
Zhang: Chinese Journal of applied mechanics Vol.3 (2000), p.1-5

Study on Creep Deformation of Reactor Coolant Pump Rotor-can during Vacuum Hot Bulge Forming Process Zhi Zhu1, a, Liwen Zhang1, b, Guanyu Song1, c and Dongjiang Wu2, d 1School of Materials Science and Engineering, Dalian University of Technology, Dalian 116023, China 2School of Mechanical Engineering, Dalian University of Technology, Dalian 116023, China acommat@mail.dlut.edu.cn,bzhanglw@dlut.edu.cn,csgyysyn@126.com,ddjwudut@dlut.edu.cn Keywords: Creep Deformation; Vacuum Hot Bulge Forming; Rotor-Can; Reactor Coolant Pump.
Dean: International Journal of Plasticity Vol. 20 (2004), p. 733 [5] M.
Hashmi: Journal of Materials and Technology Vol. 119 (2001), p. 387 [6] M.
Tisza: Journal of Materials Processing Technology Vol. 151 (2004), p. 58 [7] C.
Mac Donald: Journal of Materials Processing Technology Vol. 172 (2006), p. 346