Search results

The deficiency of bond capacity of traditional cement mortar was exposed as the new wall materials were used widely.
It produced the adverse effects on construction quality and applications of new wall materials.
Raw Materials.
Therefore, the polymer using in the test could greatly amend the bond behavior between mortars and new wall materials.
Conclusions Compared with traditional wall materials(such as clay brick), the bond strength between new wall materials and mortars were obviously lower.

Semiconductive materials as photocatalyst to degrade organics in environment raised concern both nationally and internationally in recent years.
At the same time people made lots of discussion to photocatalytic mechanism, and clearly recognized the action principle of semiconductor photocatalyst, and in terms of the choice and preparation of materials people underwent a procedure that was from blindness to definition, from simplicity to complication and from singleness to compound.
Materials Review, 2000, 12, 23-25 [2] Gao Haixia, Cheng Guofeng, Cheng Rongming, Xu Xuecheng, Chen Yiwei, Yu Huarong.
Journal of South China Normal University(Natural Science Edition), 2007,3,98-103 [9] Hong Xiaoting, Wang Zhengpeng, Lu Feng, Zhang Jun, Cai Weimin.
Chinese Journal of Catalysis, 2004, 12, 967-972

RESEARCH ON THE INTRAMODE CANNING HOT FORGING PROCESS FOR Mn18Cr18N RETAINING RING Jihong TIAN1,a , Jiansheng LIU 1,b , Huiguang GUO1, a , Huiqin CHEN1, c 1 College of Material science & Engineering, Taiyuan University of Science &Technology, Taiyuan, Shanxi, China atykdtjh@126.com b tc3rc@public.ty.sx.cn cchqsxty@yahoo.com.cn Keywords: Mn18Cr18N, retaining ring, intramode canning hot forging process Abstract.
Acknowledgment This paper was financially supported by the National Natural Science Foundation of China.
Chinese journal of mechanical engineering.
Proceedings of internation symposium on materials science and engineering.
Chinese journal of mechanical engineering.

Laboratory Test Program Experimental Equipment and Material.
The tests were conducted in the State Key Laboratory of Frozen Soil Engineering of Chinese Academy of Science.
The soil used in the current study was obtained from the embankment along the Qinghai-Tibet Railway in China.The grain-size distributions of the materials are presented in Fig. 2.
Acknowledgements This study is supported by the 973 Program of China(Grant No. 2012CB026104), the Natural Science Found of China (Grant No. 51174261) and (Grant No. 51078111), and the Natural Science Foundation of Heilongjiang Province (No.
Cold Regions Science and Technology, 2010, 62(1): 67-75

The thermographic method has been successfully applied to different materials like steels [1,2] and aluminium alloys [5,8,9].
Risitano Thermographic methodology for rapid determination of the fatigue limit of materials and mechanical components, Int.
Journal of Fatigue, (2000) XXII, 65-73
Journal of Fatigue, (1986) VIII, 29-38
Stanzl-Tschegg: Influence of loading frequency on the high cycle fatigue properties of AlZnMgCu1.5 aluminium alloy, Materials Science and Engineering: A, Volume 314, Issues 1–2, 15 (2001) 48–54

They are wildly used as; The relaxor ferroelectric materials [4, 5] memory applications [6] and as antiferroelectric materials.
Kang, "Processing, Structure, Properties, and Applications of PZT Thin Films," Critical Reviews in Solid State and Materials Sciences, vol. 32, no. 3-4, pp. 111-202, 2007
Rodríguez-Aranda et al., "Ferroelectric hysteresis and improved fatigue of PZT (53/47) films fabricated by a simplified sol–gel acetic-acid route," Journal of Materials Science: Materials in Electronics, vol. 25, no. 11, pp. 4806-4813, 2014/11/01 2014
Narm, "Effect of Y +3 and Nb+5 co-doping on dielectric and piezoelectric properties of PZT ceramics," Materials Science-Poland, vol. 28, no. 3, 2010
Srivastava, "Effect of Na on microstructure, dielectric and piezoelectric properties of PZT ceramic," Journal of materials science letters, vol. 22, no. 22, pp. 1613-1615, 2003

Smart concrete is a branch of smart materials; its origin can be traced to the cement-based electric materials obtained by combining carbon with cement by soviet scholars in the 1960s.
A factory relative to the smart materials and structures in civil engineering was built on the sustentation of National Nature Science Foundation of USA in 1993.
However, it is difficult for fabricating intact smart concrete materials with various functions according to the present science level.
[13] Fu XuLi, XiaoHuiLi and Chung D.D.L.: Improving the vibration damping capacity of cement, Journal of materials science, 33(1998), pp. 3601-3605
[35] Dry Carolyn: Passive smart materials for sensing and actuation, Journal of Intelligent Material Systems and Structures, 1993, 4(3), pp. 420-425

Most FPAEO-xMIM membranes show a room temperature hydroxide conductivity that is higher than 10−2 S/cm, which is required for AEMs materials in fuel cells.
Yang, “Fundamental studies of a new series of anion exchange membranes: membrane preparation and characterization,” Journal of Membrane Science,vol. 190(2),pp. 159-166 , 2001
Quellmalz, “Novel ion exchange membranes based on an aromatic polyethersulfone,” Journal of Membrane Science, vol. 22, pp. 325-332, 1985
Journal of Membrane Science, vol. 326(1), pp. 4-8, 2009
Driscoll, “Poly (ethylene-co-tetrafluoroethy lene)-Derived Radiation-Grafted Anion-Exchange Membrane with Properties Specifically Tailored for Application in Metal-Cation-Free Alkaline Polymer Electrolyte Fuel Cells,” Chemistry of Materials , vol. 19(10), pp. 2686-2693, 2009.

Preface The volume contains selected peer-reviewed papers presented at the AMS-II 2021 Workshop “Advances in Materials Sciences-2021,” which took place in the framework of the II International Conference on Advances in Materials Science and Technologies - CAMSTech-II 2021 on 29-31 July 2021 in Krasnoyarsk, Russian Federation.
The presented papers cover recent research results in functional materials, polymer and composite materials, chemical production technologies, metallurgy, metal science, heat treatment and processing of metals and alloys, corrosion protection, surface engineering, functional coatings, some aspects of non-destructive testing, and technological measurements.
The volume will be helpful for a wide range of scientists and specialists of research institutes, design organizations, industrial enterprises, and educational institutions interested in materials science and technologies of materials synthesis and processing.
We provided all contributors with the opportunity to publish their papers in an international, peer-reviewed journal.
DUSTOV Editor-in-chief of the journal "Development of Science and Technology", Doctor of Chemistry, Professor of the Department of Oil and Gas Engineering, Bukhara Engineering Technological Institute Bukhara, Uzbekistan Ismoil B.

However, complex and costly methods are used for design and development of such materials.
Journal International Endodonty, 40, p.462, 2007
Dental Materials, 26, p.974-992, 2010
Materials Science & Engineering: C, 32 (2), p. 282-289, 2012
Brazilian Dental Journal, 18 (1), p.3-7, 2007