Search results

Wang et al. [8] proposed a grain refinement mechanism through pulsed current-assisted rolling experiments on magnesium alloys.
Effect of titanium grain orientation on the growth of compounds at diffusion bonded titanium/steel interfaces.
Microstructural and mechanical properties of hot roll bonded titanium alloy/low carbon steel plate, Journal of Materials Engineering and Performance , 2018 , 27(4): 1664-1672
The effect of pulsed current on the shear deformation behavior of Ti-6Al4V alloy, Scientific Reports, 2018, 8(1): 14748
Preparation and properties for Ti/Al clad plates generated by differential temperature rolling, Journal of Materials Processing Technology, 2017, 249: 285-290

This study aims to investigate the effect of background color on the chromatic value of four all-ceramic system core materials at clinically appropriate thicknesses.
A colorimeter (CIE- 1976-Lab) measured the chromatic value of all samples placed on a high-noble metal-ceramic alloy and a visible light-cured dental composite resin (A2 color) background, after which the color difference was calculated.
The test materials are as follows: Z2 color system - In-Ceram ceramic sediment zirconia, Cercon base color, and Cercon base Zirconia ceramic (Degussa Co., Germany); Empress II cast ceramic (Ivoclar Vivadent Co., Ltd., Liechtenstein); 18-8 nichrome alloy, and Bio Herador N bio-type noble metal-ceramic alloy (Au 86.2%, Pt 11.5%, Heraeus Co., Ltd., Germany); and A2 color Dyract AP photo-curing compound resin materials (Dentsply Co., Ltd., USA).
The extensively applied non-tooth-color core materials are the 18-8 nichrome alloy and Bio Herador N biotype noble metal.
Ishigaki: Journal of oral rehabilitation.

Boukha et al. [15] studied the Influence of CO2-Ar shielding gas composition on the microstructure and properties of laser welded Al-Mg Alloys. 
Therefore, this work aimed at establishing suitable composition ratios of argon-CO2 shielding environment that will be adequate for GMAW of AISI 304 stainless steel to give optimum mechanical properties.
According to the previous findings of Bal et al. [19] and Abioye et al. [20], chromium carbides are hard phase secondary compounds and its formation often increases the hardness of the AISI 304 joints.
Ahmet: Journal of Materials and Design Vol. 25 (2004), p. 19-23 [3].
World Journal of Engineering Vol. 17(1) (2020), p. 87-96.

The current work is aimed to obtain the optimum holding time on microwave sintering of the composite iron-chromium reinforced with alumina particle.
International Journal of Refractory Metals and Hard Materials. 2010;28:180-6
Mondal, A.Upadhyaya,D.Agrawal, “Effect of heating mode and sintering temperature on the consolidation of 90W–7Ni–3Fe alloys,”,Journal of Alloys and Compounds 509 (2011) 301–310 [18] S.Shamsuddin, J.B Shamsul, Z.
“Liquid Phase Sintering of P/M Aluminum Alloys: Effect of Processing Conditions”, J.

Wang, Deposition of HVAF-sprayed Ni-based amorphous metallic coatings, Journal of Alloys and Compounds 440 (2007) 225–228
Chen, Cavitation erosion behavior of Hastelloy C-276 nickel-based alloy, Journal of Alloys and Compounds 619 (2015) 754–759
Li, Cavitation erosion of flame spray weld coating of nickel-base alloy powder, Wear 189 (1995) 20-24
Chenc, Laser cladding of nickel-based hardfacing alloys, Surf.
Ke, Effect of passivity on electrochemical corrosion behavior of alloys during cavitation in aqueous solutions, Wear 262 (2007) 1308–1314

Based on the results, in future restorations prepared with these materials, the properties evaluated in this work must be considered aiming the fabrication of reliable dental prosthesis parts.
Vleugels and O. van der Biest: J Alloys and Compounds Vol. 365 (1-2) (2004), p. 266
Liu: Journal Amer.
Liu: Journal Amer.

The aim of this work is to study the structural and optical properties of ZnO thin films prepared by spray pyrolysis method under different spray times.
[8] Deependra Das Mulmi, Agni Dhakal and Buddha Ram Shah, Nepal Journal of Science and Technology, 15 (2014) 111–116
Attaf, Journal of Alloys and Compounds, 509 (2011) 7267–7270

The study aimed to improve the mechanical properties of the plastic nanocomposite.
Journal of Alloys and Compounds. (2014), 615:276-82 [4] Jun J, Kim J, Bae Y, Seo YS.
The Journal of Adhesion. (2009), 85(4-5):216-38 [6] Prusty RK, Rathore DK, Shukla MJ, Ray BC.

The high extraction cost of elemental titanium from its ores is because of the high stability of its oxides and compounds due to the great affinity that titanium has for interstitials like for interstitials like oxygen, nitrogen, hydrogen and carbon.
In many of these alloys, non-toxic but heavy alloying elements like niobium, zirconium and tantalum are specifically employed [3].
Collings, Materials Properties Handbook: Titanium Alloys, in: A.
Murray, Phase Diagrams of Binary Titanium Alloys, 1st ed., ASM International, 1987
Dawson, New Titanium Alloys for Blended Elemental Powder Processing, Powder Technology, 30 (1981) 87-94

It aimed to allow the dye to be absorbed by TiO2 and form a bond with TiO2 [12].
Journal of Alloys and Compounds. 741: 1142-1147
Journal of Nano-And Electronic Physics, 9(2), 02001
Turkish Journal of Physics, 42(4), 350-355
International Journal of Electrochemical Science, 16(11), 211149