Search results

Research on the Color Difference on Surface of 3104 Aluminum Alloy Stripes during Cold Continuous Rolling Process Jianlin Sun, Guohong Ding, Lei Xia, Bing Yun, Zesheng Ji School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China Email: sjl@ustb.edu.cn Keywords: cold rolling; lubrication; surface; color difference.
Experiment procedure Experiment materials.
Surface quality of cold rolling aluminum strips under lubrication condition[J].Journal of University of Science Technology Beijing, 2008, 15(3): 335-338
Lubrication in strip cold rolling process[J], Journal of University of Science Technology Beijing, 2004, 11(4): 368-372
Materials Science and Engineering, 2003, A350: 81-85

The use of natural fibers in this process is inexpensive and such materials can be referenced as biocomposites, saving the primary raw material.
Introduction Composite materials can be characterized as systems that take advantage of its partial phases [1-2].
The most common type of composite materials is primarily long-fiber composites with arranged fibers.
Sisal fibers are used, for example, for increasing the strength of polymeric materials.
Araújo Rohen, et al.: Tensile behavior of epoxy composites reinforced with thinner sisal fibers: Materials Science Forum, Vol. 869 (2016), p. 249-254 [8] K.

The properties of longitudinal bar, stirrup, steel angle and steel flat were tested according to GB/T 228-2002 Metallic materials -Tensile Testing at Ambient Temperature, the test result is presented in Table 2.
References [1] Lin Youqin, Gong Guang, Zong Zhouhong, Test research on concentric axial compression of concrete short columns reinforced outside by steel plank, Journal of Fuzhou University (Natural Science), 30 (2002) 221-224 (in Chinese)
[4] Lu Zhoudao, Liu Changqing, Zhang Kechun, Wang Huanjie, Experimental study on the seismic performance of enveloped steel strengthened RC frame joint, Journal of Sichuan University (Engineering Science Edition), 42 (2010) 56-62 (in Chinese)
[5] Pan Zhihong, Li Aiqun, Nonlinear static analysis on RC column strengthened with externally bonded steel frame based on fiber model, Journal of Southeast University (Natural Science Edition), 39 (2009) 552-556 (in Chinese)
Journal o f Structural Engineering, 129 (2003) 725-732

The fabric manufacturing and additional treatments originate variations in roughness of fabric materials which initiate yarn irregularities [4].
Acknowledgements This study was financially supported by project KIK 19019 "Developing of textile waste shredding technology and innovative materials to adding value to textile waste and support the circular economy”.
International journal of clothing science and technology. 2002
Mazal, Image analysis method of surface roughness evaluation, International Journal of Clothing Science and Technology. 2007
Kumar, Designing and development of denim fabrics: Part 1 - study the effect of fabric parameters on the fabric characteristics for women's wear, Journal of Textile Science and Engineering. 6(4) (2016) 1-5

"Extrusion of AA 2024 Alloy," Materials science and technology, V 9, May 1993, 430-440.
Computational Materials Science, v 27, n 3, 2003, 250-258. 4.
"Computer modelling of microstructure during hot flat rolling of aluminium," Materials Science and Technology, Vol. 8, n. 1, January 1992, 72-77 8.
Materials science and engineering A.
Modelling and Simulation in Materials Science and Engineering.

Science and technology of advanced materials, 11(5), 054504
Journal of Materials Chemistry, 20(38), 8207-8223
Journal of Materials Chemistry C, 1(15), 2735-2743
Materials Today: Proceedings
Journal of materials science, 45, 3259-3265

Metallurgical and Materials Transactions. 43-1 (2012) 124–135
Zhurko, Chemical composition effect on VVER-1000 RPV weld metal thermal aging, Journal of Nuclear Materials. 465 (2015) 540-549
Moffat, Vibratory stress relief: a fundamental study of its effectiveness, Journal of Engineering Materials and Technology. 102-2 (1980) 169–176
Series: Materials Science and Engineering 156 (2016) 012007
Series: Materials Science and Engineering, 156 (2016) 012011

Metal materials are very important engineering materials, which are irreplaceable in the history of mankind.
As an important component of materials, metal materials are irreplaceable materials in engineering applications.
The wetting property is the basic property of material surface, and it is the fusion of material science and surface applied science.
Progress in Materials Science, 2011, 56: 1–108
Journal of Materials Chemistry A, 2017, 5: 31–55

Titanium alloys and their machinability - a review, Journal of Materials Processing and Technology, vol. 68, pp 262–274
Evaluation of principal wear mechanisms of cemented carbides and ceramics used for machining titanium alloy IMI 318, Materials Science and Technology, vol. 2, pp 47-58
On tool materials for high speed machining, Journal of Engineering for Industry, vol. 109, pp 87-91
Wear mechanisms of ultra-hard cutting tools materials, Journal of Materials Processing Technology, vol. 115, pp 402-412
Microstructural analysis on boundary sliding and its accommodation mode during superplastic deformation of Ti–6Al–4V alloy, Materials Science and Engineering, vol.

Experimental Section Materials.
The materials were purchased from Aladdin.
Xing: Organic matter–surface area relationships in acid soils, Soil Science Society of America Journal.
Frimmel: Adsorption of humic substances onto kaolin clay related to their structural features, Soil Science Society of America Journal.
Schlautman: Molecular weight fractionation of humic substances by adsorption onto minerals, Journal of colloid and interface science.