Search results

So, this work aimed to prepare Si nanosize by magnessiothermic reduction and Mg nanoparticles can be prepared by solution route method.
Alloys and Compounds 587 (2014) 807–811
Alloys and Compounds 565 (2015) 707–711
Alloys and Compounds 720 (2017) 529- 540
Journal of Power Sources 175 (2009) 657-897

Toward this aim, the influence of the chemical nature of the carrier gas (either H2 or Ar) on the quality of the P+ deposit and the electrical characteristics of the P/N junction was investigated.
After the VLS sequence, the residual Al-Si alloy was wet etched using alternates of acid and basic solutions.
We believe that the pits are the visible imprints of Al4C3 parasitic inclusions because this compound gets more stable when the Si content of the liquid phase gets too low [3].
a b Figure 1: Surface morphology after etching of the remaining alloy on samples grown by VLS using (a) H2 , and (b) Ar as the carrier gas.
Journal of Materials Science 25 (1990), 1842-1850.

Microcosmic analysis and plastic deformation tests of the bonding interface were also executed, aimming to study the interface properties and provide research basis for follow-up pressing working of complicated shape workpieces .
According to the Cu-Fe two components alloy phase diagram, no brittle Cu-Fe intermetallic compound generates in Cu-Fe alloy and the microcosmic structure appears as Cu-Fe solid solution[6].
JOURNAL OF NORTH CHINA INSTITUTE OF TECHNOLOGY, 2003, 24(2):94-97.

The aim of the paper is to investigate EPE and its influence on the deformability, structure and functional properties of TiNi alloys in austenite and martensite states.
The microhardness of both alloys decreased as a result of annealing.
Both alloys demonstrate the same behavior at unloading.
At heating, these alloys demonstrated the shape memory effect (Fig. 13b), but in the initial state it is low (2.5–3.5 %) for both alloys.
Stolyarov, Shape Memory Effects in TiNi-based Alloys Subjected to Electroplastic Rolling, Journal of Materials Engineering and Performance, 23 (2014) 2391-2395.

This study is aimed at obtaining high dispersed phosphors with the composition of Y2O3:Eu and Y3Al5O12:Eu (YAG:Eu) with the use of different methods of synthesis and at investigating the influence of the method and conditions of synthesis on these substances physico-chemical and luminescent properties.
Yen-Pei Preparation of Y3Al5O12:Eu powders by microwave-induced combustion process and thei luminescent properties, Journal of Alloys and Compounds, 402 (2005) 233-236

The outer layer of multilayer protective coatings shall include oxides of refractory metals or oxide-forming compounds such as borides and silicides or pure metals capable of forming protective oxide films on the surface.
For stabilization of ZrO2, HfO2 oxides in tetragonal or cubic modifications or as part of a compound with phase stability in the temperature range from room to intended operating conditions, compounds of rare earth elements, most often lanthanum, can be introduced [85].
Alloys Compd. 206 (1994) 237-242
Alloys Compd. 662 (2016) 302-307
Alloys Compd. 682 (2016) 203-207

This would indicate the equality of diffusion of components in binary alloys.
It permits to calculate correlation factors for solute and solvent diffusion in substitutional alloys.
Among these were intermetallic compounds, metallic glasses, quasicrystals, elemental and compound semiconductors, and ion-conducting materials.
[47] DIMETA-82, Diffusion in Metals and Alloys, F.
[48] DIMETA-88, Diffusion in Metals and Alloys, F.

This research work aimed to apply the aluminium dross, waste of ADC12 and 6063 aluminium smelter grade as the raw materials produced plant fertilizer by acid treatment process with phosphoric and hydrochloric acid.
The dross contained various compounds, the commonly compounds, and their respective content are as follows: Al2O3 64.8%, CaO 0.98%, SiO2 4%, Fe2O3 1.5%, MgO 3.2%, Na2O 2.75%, K2O 0.51%, Cl 3.9%, C 1.25% and S 0.22% by weight [3].
Hong et al. [6] passed recycled aluminium through a submerged and an electric arc furnace to produce an Al-Si alloy and brown fused alumina, respectively.
The aim of this research work was to stabilized aluminium dross by acid neutralization to make a plant nutrients.
Tani: Rajabhat Journal of Science, Humanities & Social Science.

Due to its intriguing nature and controversial suggestions, this paper aims at experimenting the low-carbon steel affected by the pre-deformation via internal friction in order to investigate its affect on hardening properties of steel.
Journal of Alloys and Compounds (2000) vol. 310, p. 405-410

In many ceramics, as in the case of ferrites, there is reaction of forming new solid phases, polymorphic transformations, decomposition of compounds to form new crystalline phases [13].
In this context, this study aims to evaluate the sintering in a conventional oven and microwave oven nanopowders of Ni-Zn ferrite synthesized previously by microwave energy and thus develop materials with microstructures appropriate for the development of soft magnetic materials.
Date, Indian Journal of Chemistry, 35, (1996), p. 353-365
Alloys.