Search results

Experiment results show that the noise reduction effect of the wavelet packet based on the adjusted threshold is obvious and the SNR of signals is also improved.
The wavelet packet coefficients which are less than or equal to the threshold are set as zero, and just the data which is greater than the threshold is used for rebuilding signal.

Wiebeck et al. [25] presents thermal conductivity data of synthetic polymers (EPS and XPS - 0.038 W / m.K).
Data is collected using the FieldChart software, transferred to spreadsheet format file, and analyzed later.
The software was programmed so that the data collection of the temperature sensors occurred every 1 minute, in which for each sample a hundred data were collected.
The temperature data are expressed graphically by the temperature range in which they were included.
The data presented in Graph 5 represent the performance for average temperatures of 50 ° C and 60 ° C.

The proposed model was validated against experimental data and it showed simulating and experimental results are in very good agreement at three different rotational speeds, in particular near the surge line, though the deviation begins to increase as mass flow rate goes up.
Anyway, in many cases, a limited operating domain of the turbocharger device is really available, and various maps data extrapolation techniques are commonly included within commercial 1D codes [8, 9, 10].
As shown in the figure, the simulation results match very well with experimental data in the neighbourhood of the surge line.
Figure 4 Comparison between the model 1 simulation results and experimental data SIMULATOIN RESULTS The main geometry data and other numerical values used in Centrifugal Compressor Model are presented in Table 1.
The proposed model was validated against experimental results and the simulation results match very well with experimental data except the high mass flow rate area.

.% Sn can nicely reproduce the experimental data.
As temperature decreases and interface velocity increases, both the maximum solute concentration as well as the spatial penetration of the liquid concentration profile diminishes, which demonstrates a reduction of solute segregation at the interface and an occurrence of the solute trapping.
Figure 4 displays the calculated solute segregation coefficient profile according to the present phase simulation, compared with the experimental data from Smith et al. [15].
As can be seen, the experimental data can be nicely reproduced by the simulation with the optimal interface width and the interface permeability, which are chosen according to the optimal sets discovered by Zhang et al. [16].
Comparison between the presently simulated solute segregation coefficient k(V) as a function of the interface velocity in the Al-0.2 at.% Sn alloy and the experimental data from Smith et al. [15].

The exchanged and used information and corresponding data models within the functions and services are addresses in the information layer.
The use case steps receive additional information concerning their linkage within the SGAM Framework and the data concerning the communication layer of the SGAM.
According to the exchanged information in the related steps, the relevant data for the use case information exchange table can be derived in step 4.
In the requirement fields, the data to display in the communication layer of SGAM is entered.
In the respective requirement field, the data for the information layer of SGAM is listed.

The method to be carried out is by using laboratory experimental methods, namely by carrying out various kinds of tests in connection with previously planned data using the SNI-7656-2012 [6] mix design.
Test Object UTM Machine Fig. 5 - Concrete Compressive Strength Testing Procedure Phase 4, from the results of the tests carried out in phase 3, data analysis was carried out.
Data analysis is a discussion of research results, then from these steps, research conclusions can be drawn.
Testing for characteristics produces data used in concrete mixing (mix design).
Before printing on the cylinder, a slump test is carried out first, The data from the slump test results are in accordance with the research plan, namely 75 mm – 100 mm.

XRD data show that the sample on the basis of orthorhombic unit cell can be attributed to Pmn21 space group.
Other results obtained (EDX, AAS) correspond approximately to the theoretical data.
The results demonstrate that the data obtained have good convergence with the theoretical ones.
Reduction of capacity occurs owing to amorphousness of the structure and unstable position of Mn in the crystal structure of the material.

The following data was collected: TABLE II.
The graph shows cluttering of data points at high frequency.
In this technique the data points are averaged, so that in each of the N adjacent frequency level there is equal number of data points.
This reduction of data points makes the PSD plots easier to comprehend.
The data logging can be improved by including a checksum check.

Based on the above, the housefly maggot anti-inflammatory parts could regulate the endothelial cell dysfunction through decreasing cell proliferation and migration and a reduction in VEGF expression might plays a key role in this process.
Data were collected and analyzed by FACSCalibur.
All data were expressed as the mean ± standard error of the mean (SEM).
The Student-t-test was applied to compare means of data of two independent samples.

Statistical analysis of the data was provided by the manufacturer.
Table 1 Correlation between the data under 0.05 significant level.
So the defect rat of the statistical data can be used to reflect the purity level of the molten aluminum and also can be used as the data basis of the numerical simulation.
The effect picture of c can be obtained through these statistical data.
The result is same in the change trend between simulation and experimental data.