Search results

Key Engineering Materials, Vol. 450(2010), p.63-66 [3] Z.
Advanced Materials Research, Vol. 129(2010), p.1181-1185 [4] Z.
Journal of Central South University of Technology, Vol.15 (2008), p.245-249 [6] S.
Advanced Science Letters, Vol.4(2011), p.2738-2743
Applied Mechanics and Materials Vol. 121 (2012), p. 3477-3480

Materials and Method Cement.
Materials & Design. 37(0): p. 443-449
Journal of Materials Science (Norwell), 2003; 38(15): 3159 – 3168
ACI Materials Journal (Detroit), 1996; 93(6): 629-636
The international journal of minerals, metallurgy and materials, volume 19, Number: 3, Mar 2012, page 252, DOI: 10.1007/s12613-012-0547-9

The shell materials were varied: aviation aluminum and titanium alloys, high-strength steels and heat-resistant alloys (Fig. 1).
Yudenkov, Time relaxation of point defects in p- and n-(HgCd)Te after ion milling, Journal of Electronic Materials. 32(7) (2003) 698-702
Balalayeva, Effect of particular combinations of quenching, tempering and carburization on abrasive wear of low-carbon manganese steels with metastable austenite, Materials Science Forum. 945 (2019) 574-578
Key Engineering Materials, 864 (2020) 285-291
Gurenko, Modeling dynamic parameters of hard alloys during shock wave regeneration, IOP Conference Series: Materials Science and Engineering. 969(1) (2020) № 012079

Material.
Medium carbon steel with the series of SAE 1045 was used as the materials throughout the experiments.
Besides that, the behaviour of the materials during the fatigue test can be observed by segmenting the signals into severals periods of time prior to failure.
Izawa: Journal of Nuclear Science and Technology Vol. 39(2002), p. 514
Al: Journal of Science and Technology of Advanced Materials (2007)

Náhlík7,g Institute of Physics of Materials, AS CR, and Institute of Solid Mechanics, Mechatronics and Biomechanics, BUT Faculty of Mechanical Engineering; Brno, Czech Republic 2Institute of Physics of Materials, AS CR, Brno; Czech Republic 3Polymer Competence Center Leoben GmbH, Roseggerstrasse 12, 8700 Leoben, Austria 4Material Science and Testing of Polymers, Montanuniversitaet Leoben, Otto Gloeckel-Straße 2, 8700 Leoben, Austria 5,6Montanuniversität Leoben, Austria 7CEITEC IPM, Brno, Czech Republic aslavik@ipm.cz, bhutar@ipm.cz, cmichael.berer@pccl.at, danja.gosch@unileoben.ac.at, eflorianarbeiter@uniloeben.ac.at, fgerald.pinter@unileoben.ac.at, gnahlik@ipm.cz Keywords: fracture mechanics, failure of polymer bearings, mixed mode, numerical modelling Abstract.
Study of fatigue of roller bearing elements made of POM (Polyoxymethylene) and a general lack of knowledge about fatigue of materials in mixed modes caused a need to design a special specimen loaded under mixed mode conditions.
Schirmeisen: International Journal of Fatigue Vol. 62 (2014), p 93 [2] J.
Sih: Journal of Basic Engineering Vol. 85 (1963), p. 519 [9] M.R.
Aliha: International Journal of Solids and Structures Vol. 46 (2009), p. 311

Unfortunately, these materials used by the industry are very expensive.
Activated carbon is an adsorbent material obtained from carbon-rich materials that can be of plant or mineral origin.
The use of these materials in this work is of twofold interest: (i) to elaborate activated carbons at low cost, (ii) to valorize the wastes in order to give them an added value.
Material and Methods II-1.
After cooling, the materials obtained were washed abundantly with distilled water until the pH of the rinsing water was between 6.5 and 7, then dried in an oven at 105 °C for 24 h.

Teo: International journal of adhesion and adhesives.
Osiyemi: Journal of Materials Science Letters.
Williams: Journal of Composite Materials.
Zavattieri: Composites Science and Technology.
Needleman:Modelling and Simulation in Materials Science and Engineering.

Materials and method Materials.
Journal of applied polymer science, 2003. 44(1): p. 151-158
Materials letters, 2006. 60(6): p. 805-809
Journal of applied polymer science, 2003. 49(4): p. 617-621
Journal of Materials Science, 1980. 15(11): p. 2884-2888.

According to Science Citation Index Expanded and Social Sciences Citation Index Database in web of science, only 12 records were found in related discipline when “keyphrase extraction” as search title.
The World Wide Web has been widely used by enormous students for acquiring information, learning materials and references.
In order to find reliable and trustworthy materials, students must sift through the millions of pages available on the web, thus Kilbride J and Mangina E. (2005) describe a system designed to assist students of a web-based learning environment to achieve either acting autonomously or assisting users to create queries.
INTERNATIONAL JOURNAL OF INTELLIGENT SYSTEMS, 2010; 25(12): 1158-1186 [2] Wan Xiaojun, Xiao Jianguo.
Automated keyphrase extraction: Assisting students in the search for online materials.

Fig.8 Numerical simulation and experimental Fig.9 Load-displacement curves load displacement curve of different materials Stress distribution of different masonry materials.
Masonry materials of filler wall is the main factor for filler wall’s failure mode.
Journal of Structure, ACl, 1986, 83(5): 567-576
Xi 'an metallurgical construction academy of sciences journal,1982,14(2):1-13 [6] FEMA 356 (2000).
Journal of the Structural Division.