Search results

All data presented in Table 1 and Figures 1-5 are representative of at least three independent experiments in which all samples were assayed in triplicate.
The above data demonstrated that an ultrasonic treatment duration of 20 min was optimal for the dissolution of organic matter and release of carbon elements from excess sludge.
The data obtained revealed a strong correlation between the COD and TOC of sludge supernatant.
[2] Rai CL, Struenkmann G, Mueller J, Rao PG. (2004) Influence of ultrasonic disintegration on sludge growth reduction reduction and its estiomation by respirometry.

That make noise reduction be one of the key problems in image processing and the basis of image subsequent processing.
At last, to MRI image we pay particular attention, experiments data show that our algorithm has excellent performance. 5.
The Rician distribution of noisy MRI data[J].

Introduction Due to its unique porous structure , metal foams have a series of special properties, such as good acoustic, noise reduction, electromagnetic shielding, damping and so on, and it is a new lightweight structural and functional material[1-3].
The structure size data of model is shown in Table 1.
Table 1 The structure size data of model.

If the obtained execution probability of transition by calculation in this time is , namely the execution probability of timed transition is , the total average delay time of timed transition after reduction is: (2) On the basis of , it can construct a selective switch, to generate a selected structure, it can be converted into an instantaneous transition, and is applied to describe. by analysis, it can be seen that and are able to integrated, to build a new sequential structure, it can reverse to make it forming an instantaneous transition which is described by , and through the calculation, the time delay of it is 0.
In order to calculate the probability of steady state of each identification, the formula (3) is applied to calculate the corresponding probability, this introduction is used to describe state differential equation, and to obtain the steady state of each identification as follows: (6) Because and are failure state, the compatibility of sub-software is shown as follows: (7) Based on the compatibility of sub-software and, can obtain the compatibility of service combination can be obtained as follows: (8) 3 Analysis of simulation result The proposed algorithm is used to make simulation experiments to verify the performance, analyze the related data, and make the following setting: In the sub-software of Android system, if the concurrent structure similar to the has a lots, the amount is represented by , when becomes bigger, the value of are =1, =2 and =3.
Table 1 Compatibility of sub service Time （h） Compatibility n=1 n=2 n=3 10 0.9977 0.9989 0.9990 50 0.9830 0.9942 0.9945 100 0.9678 0.9888 0.9895 150 0.9365 0.9778 0.9786 200 0.9066 0.9677 0.9688 250 0.8794 0.9562 0.9576 300 0.8499 0.9458 0.9469 It can be seen from table 1, the compatibility data of sub service is obtained, and the tendency chart of compatibility changing of sub service is shown as figure 5.

Fuzzy Comprehensive Evaluation Basic principles In this paper, rough set theory [5] for the reduction of the index set to achieve the targets simplification [6] effect, and on the evaluation index weights were determined using subjective weights and objective weights combining [7] method, is a more effective response evaluation of each indicator on the evaluation results. 2 Fuzzy comprehensive evaluation model based on rough set 2.1 Index System Through the power supply enterprise research, evaluation of various factors according to the relevant technical staff are given the impact of the wire strength, combined with a lot of actual data, results of the evaluation circuit 110kV voltage level of basic indicators.
A fuzzy neural network based green evaluation method of power enterprise data center[J], Power system Technology.2008,32(19):84-88,97

The cast alloy was extruded with a reduction ratio of 19 at the temperature of 573 K.
Including are the data of a dual-phase Mg-Al alloy (Mg-30.7at.
Including are the data of dual-phase Mg-Al alloy.

Result and Discussion Experimental results Under the condition of invariable natural gas flow rate (10.5L/min)， experimental data were recorded at 1.5th hour and 3rd hour after ignition and it was found that the steady state combustion was achieved after 3 hours.
Fig. 4 shows the experimental data at 3rd hour.
Combustion control technologies of catalytic burner applying to reduction-included furnace.

Significant reduction of the substrate thickness and only minor changes of the drop volume during wetting experiment at 1573 K were detected for the CaF2/Ge system (Fig.3). .
The standard thermodynamic data were extracted from [10].
[10] SGTE Substance, Thermodynamic Data-Base SSUB3.

The experiment temperature was 260℃～410℃, and the strain-rate was 0.001～10s-1, and reduction was 50%.
(5) Analysis of results According to the experiment data, the curves of and and can be obtained, seeing Fig.2-3.
According to formulas (3),(4) and (5), the coefficients (n,α,Q,A) can be determined at different strain by experiment data.

Introduction Hot forming High Strength Steel (HSS) is widely used in body structure as a solution for weight-reduction of automobiles [1-2].
The program flow for data processing is shown in Fig.3.
Program flow for data processing of MBN.