Search results

References [1] Mahdi, A.S., Mahamad, A.K., Saon, S. et al. 
Al-Musawi, Bashar Mahmood Ali, Sameer Algburi, Haitham M.
Alzoubi, Ali Khudhair Al-Jiboory, Aws Zuhair Sameen, Hayder M.
[12] Sarang, S.A., Raza, M.A., Panhwar, M. et al. 
[19] Abouzeid, A.F., Eleraky, H., Kalas, A. et al. 

Abid4, A.L.
Zidani et al. [12] have noted that this random orientation of the cementite lamellae leads to a heterogeneous microstructure in the section of wires [12,19,20].
Al-Kassab, C.
Farh, A.L.
Messaoudi, et al, Mechanical behavior and texture evolution study of medium carbon steel wires during industrial wire-drawing process, in: Proc. 28th Int.

Engeln et al. [2] examined the uniaxial extension of polytetrafluoroethene (PTFE).
El-Tonsy et al. [3] observed the behaviors of polypropylene (PP) and high-density polyethylene (HDPE) during stretching.
Compañ et al. [8] investigated co-extruded linear low-density polyethylene films.
Ishihara et al. [9~11] observed PET films after stretching.
El-Tonsy, M.S.

The Effect of Process Route on the Mechanical Properties and Microstructure Aluminum Al-Si-Cu-Mg-Mn Alloys Rahmawaty1,a, Surya.
In the present work, the solution treatment was applied to Al-Si-Cu-Mg-Mn alloy.
The microstructure of Al-Si-Cu-Mg-Mn Alloys sample is shown in Figure 1.
Jorge, “High Strength AA7050 Al alloy processed by ECAP: Microstructure and mechanical properties,” Mater.
Abd El Aal and M.

El-Samak, D.
Adham, M.A.A Al-Maadeed and A.
El Gheriany, F.
Ahmad El Saqa, A.
Abd El Razek Amer and M.

Meanwhile, Bossert et al. [2] have shown that anonymity Anonymity is defined so that every generation is assigned same weight, such as “0” or “1”.
The extended utility function diverges to negative infinity as the probability approaches a certain level, referred to here as the “extreme line” (EL).
In this case, the EL could be given by .05.
Therefore, society would control the probability less than EL in the FDF.
Let the level corresponding to the SL be denoted by GS, and the level corresponding to the EL by GU.

Li, et al. [4] have developed a semi-numerical approach to solve for the stresses in the cracked laminate under bending.
According to the plane cross-section assumption, the strain distribution of the cross-section at far field for the model is assumed to be linear, that is .(1) where EL is the longitudinal elastic modulus of unidirectional composite.
Table 1 Basic data of cross-ply laminates Material type EL (GPa) ET (GPa) GL (GPa) GT (GPa) Gm (GPa) t (mm) Glass/epoxy 50.0 15.20 4.70 3.28 1.26 0.2 Graphite/epoxy 130.0 9.70 5.00 3.60 1.26 0.2 Assume the total number of sub-layers N = 2m+2k =40 and crack spacing is 0.8 mm (4t) [8].
Oham, et al.: Reinf.

We take the longitudinal average strain as follow )1(sinh )cosh( ) )cosh( ))/(cosh( 1( 1 1 1 1 0 00 9090 0 1 00 9001 00 9090 0 0 00 900 0 0 0 0 1 1 l a a aaEEt Et Elal tE tt l a dx aEt lxaEt El dx tE tt l dx El c x x c c al x c c l al l xx xxc − + − + + = + + + = =≈ ∫ ∫ ∫ − − η η σ η σ σ η η σ σ σ εε � � � ���� Defining n as the delaminate propagation rate, 1a is half of the delaminated crack length.

The model of the aqueduct is subjected to the NS component of the 1940 El Centro earthquake, in simulation, the PGA is adjusted to 0.4g.
(a) mid span (b) 2nd span Fig.2 Responses of aqueduct due to El Centro earthquake The force of the MR damper and the LQR force are shown in Fig.3.
[2] Yi F, Dyke S J, Caicedo J M, et al.(1999) Seismic Response Control Using Smart Dampers [J].
[4] David A S, Paul N R, Lin Pei yang, et al.(2007) GA-optimized fuzzy logic control of a large scale building for seismic loads [J].

For actual applications, emitted light wavelength under 300nm is essential but higher Al composition is also relatively necessary for material growth.
Trimethylgallium (TMG), trimethylaluminum (TMA), bis-magnesium (Cp2Mg), silane (Si2H6) and ammonia (NH3) were used as Ga, Al, Mg, Si and N sources, respectively.
Current-voltage characteristics of the 290nm UV LEDs with 5um-thick and 20um-thick GaN buffer layers The electroluminescene (EL) spectra measurement of the UV LEDs are shown in Fig.3.
EL spectra measurement of the UV LEDs with various injection levels The power measurement is performed by using an integrating sphere which is placed close to the surface of LEDs with a distance of 1cm.