Search results

Introduction The growth in use of composite panels has been increased lately by the construction industry's need due to the ease of mounting to the building sub- structure, reduction in building times with spin off savings in labour costs.
According to previous study, FEM has substantially decreased the production time while providing relevant data [7].Both specimen are modeled using Creo Parametric 2.0.
Variation of mesh size related to number of element and node for TET10 is giving higher relevance of data set.
The comparison of the analysis between Trim-deck and Span-deck panel has been made and this results will then be compared with the experimental data for validation.
The finite element modeling proposed can be used to simulate the experimental data and help to reduce the cost and time consumption compared to previous experimental setup.

If the die roll height of the power transfer part like gear is large, then a structural defect can occur due to the reduction of the power transfer surface.
The die roll heights on the corner shape of the fine blanked parts were measured with an optical measurement inspection system (Data star 200) and Table 3 shows the measured data.
[a] [b] [c] Fig. 6 The fine blanked samples from the 1st experiment(a), the 2nd experiment(b) and the 3rd experiment(c) The measured data of the die roll heights on the corner shape of the fine blanked parts were analysed and then two graphs were created as shown in Fig. 7.
Table 3 Measured data of the die roll heights on corner shapes of fine blanked part Corner shape V-ring distance Radius[mm] Angle[º] D=1.8 mm D=2.3mm D=2.8mm 0.5 30 1.156 1.250 1.292 45 1.139 1.158 1.248 60 0.932 0.954 1.059 90 0.776 0.81 0.854 120 0.685 0.712 0.742 1.0 30 0.902 0.983 1.037 45 0.896 0.935 0.975 60 0.837 0.882 0.936 90 0.751 0.762 0.815 120 0.659 0.67 0.734 1.5 30 0.716 0.745 0.798 45 0.712 0.731 0.784 60 0.705 0.718 0.765 90 0.658 0.691 0.736 120 0.577 0.588 0.624 2.0 30 0.633 0.651 0.661 45 0.628 0.639 0.647 60 0.612 0.625 0.644 90 0.544 0.563 0.606 120 0.453 0.461 0.491 Fig. 7 Die roll heights depending on the V-ring positions and corner shapes Summary It should be noted that the die roll height on the corner shapes of fine blanked parts increases with increasing the V-ring distance.

A second set of data further point to microdefect influence on metal impurity gettering.
This data has been used in the modeling studies in the Refs. [14].
Experimental data for the diffusion constant of H in Si, D, vs. temperature.
Other data represent H diffusion in Si with various degrees of trapping (see Ref. [15] for more explanations).
CrB recombination and concentrations also were measured, but this data is not reproduced here.

It might be concluded that a reduction of the rate of silver dissolution from the bioactive gel-glass might preserve a maximum cell viability.
Discussion and Conclusion Previously published data have shown that the ionic products released from the gel-glasses (such as biologically active calcium and silica) have the ability to stimulate cellular differentiation and proliferation, and there appears to be an up-regulation of certain genes that are implicated in the growth and proliferation of these cells [6].

Load–displacement curves and mechanical properties are shown using data from experimental works.
Based on the data obtained from LH and HL sandwich panel, it is apparent that the energy absorption capacity of HL sandwich panel is 6.2% slightly higher than LH sandwich panel.
From the data collected, it obviously shown that the change of density affects the bending strength of the sandwich panel.
After reaching peak load, each curve flattens out with no reduction of loading capacity.

These data would be a foundation for the appication of DBLP in antitumor, which indicated that DBLP would be a potential antitumor drug.
Although the efficacy of chemotherapy for the majority of cancer types has improved over the last three decades, high toxic effects of chemotherapeutic drugs causing a severe reduction in quality of life are still formidable problems in clinical medicine[3].
The sections of liver showed that central vein and hepatic lobule were distinct, hepatocellular disposed compact and orderly (data not shown).
Analysis the activity of GPT and GOT of blood serum in mice bearing U14 cervical carcinoma The GPT and GOT activities of blood serum were also determined and the data were showed in Table 2.

Data from the measurements were used for creation of new RHT concrete models in Autodyn.
Level of the resistance was set by projectile velocity reduction after sample perforation.
Numerical simulation was validated by experimental data and experiment setup.
Results of numerical simulation and their comparison with experimental data Material Residual velocity Experiment /Simulation Experiment [m/s] Simulation [m/s] FRC 346 328 1.06 UHPC 260 239 1.09 UHPFRC 2 % 71 58 1.22 (a) (b) (c) Fig. 4.

The kinetic data was best described by the pseudo-second order.
Heavy metal that contained in water can be separated with many methods such as reduction, membrane process, ion exchange, solvent extraction, and adsorption [1,2].
All of these peaks are consistent with JCPDS data 39-1894 [11] with a very small shifting in 2q expected to be due to the interaction between HAp and chitosan.
Watanabe: Macromolecules 17 (1984) 973-975 in JCPDS – International Centre for Diffraction Data, 1998

Both Healthy and Faulty LRB conditions data were collected for 10 minutes each, which is adequate for 10 sets of data divided into training, validation, and testing with a fixed 6:2:2 ratio, respectively.
For example, [11] trained a U-Net model constructed by multiple CNN layers using the seismic field data collected at Hussar, Alberta, by the CREWES Project and found that the noise reduction obtained using their neural network architecture shows considerable promise in seismic data processing.
The SHM heavily relies on high-quality data, yet the real application environment and imbalance between good and faulty data collected become challenges in achieving high accuracy of predictive models [12].
Raw vibration data were acquired from both healthy and faulty LRBs.
Stewart, Attenuating coherent environmental noise in seismic data via the U-net method.

These accelerometers have internal storage capability but do not transmit data wirelessly; data needs to be downloaded to a computer after test completion.
The recording unit guarantees that there are no data losses in case of failure of power supply or the Internet connection.
Identification and monitoring of bridge health from ambient vibration data.
Random data: Analysis and measurement procedures.
A framework for reliability assessment of an in-service bridge using structural health monitoring data.