Search results

The study operated BM II according to the standard test method of using the BM II published by the American Society for Testing and Materials (ASTM)[13].
The COF measurements results showed that no matter footwear materials were treated or non-treated, the COF was higher than the standard suggested by ASTM (COF=0.5) under dry floor condition.
Matz, The Slip Resistance of Common Footwear Materials Measured with Two Slipmeters, Applied Ergonomic. 32 (2001) 549-558
American Society for Testing and Materials, F-1677-96, Standard method of test for using a portable inclinable articulated strut slip tester (PIAST), Annual Book of ASTM Standards. vol. 15.07(2005).
West Conshohochen, PA, American Society for Testing and Materials

Experimental Materials.
An: Journal of Composite Materials, Vol.42 (2008),p.173 2.
W.Y.Zhou, S.H.Qi and C.C.Tu: Journal of Applied Polymer Science, Vol. 104(2006),p.2478 5.
C.G.Ma, Z.M.Rong and M.Q.Zhang: Journal of Materials Engineering, (2002),p.40 (in Chinese) 17.
S.F.Li: New Chemical Materials, Vol. 30(2002),p.11 (in Chinese) 18.

It is an efficient way to improve the effect of infrared camouflage through phase change materials to reduce the exterior temperature.
As phase change materials in the phase transition progress will absorb or release large amount of latent caloric, it can make its temperature almost constant.
With optimized to Kraton resin (K10) as the membrane material, infrared camouflage coatings were made with, thickness 2.2mm.
[J]. polymer the international journal for the science and technology of polymers.
[J].Materials Review.

Acknowledgements This research was supported by the National Natural Science Foundation of China, under Grant No. 50775197.
JOURNAL OF MECHANICAL ENGINEERING, 2009, 48(8)：255-260
JOURNAL OF MECHANICAL ENGINEERING, 2009,45(6)：211-215
Journal of the Mechanics and Physics of Solids, 2009, 57(4)：706-727
Advances in discrete element methods for particulate materials[J].

The production and consumption of plastic materials has exceeded that of steel, aluminum and copper if it is calculated by volume and the plastic materials becomes to be the largest consumption material in the world.
Therefore, these three kinds of materials show obvious biodegradability.
This means that these two materials can not be biodegraded by these fungi.
Table 2 shows the biodegradability of different materials by size.
Briassoulis: Journal of Polymers and the Environment,Vol. 15 (2007), p. 125

Materials and Methods Materials.
Compared with other porous cementitious materials, the ability of adsorbing water is worse, leading to less early shrinkage [8].
Fig.5 Influence of a combination of both materials on early shrinkage Influence of a combination of both materials on early shrinkage of ordinary concrete.
(in Chinese) [5] Hong Yang: Journal of Fujian Building Materials, 2007, 3:35-37.
(in Chinese) [6] Mingji An, Jinquan Zhu, Yafeng Ma: Journal of China Academy of Railway Sciences, 2006, 27(4): 27-31.

Hot deformation behavior of Al2O3/Cu-10vol%WC composite Feng Jiang1, a Tian Baohong1, 2, b, Liu Yong1, 2, c 1 School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471003, China 2 Henan Key Laboratory of Advanced Non-ferrous Metals, Luoyang 471003, China a fhap256@163.com, b bhtian007@163.com, c lyly2008@163.com Keywords: Al2O3/Cu-10vol%WC, Deformation behavior, Constitutive equation, Microstructure.
Lin: Materials Science and Engineering A, Vol. 418 (2006), p. 137-145 [2] P.K.
Lin: Materials Science and Engineering A, Vol. 429 (2006), p. 58-65 [3] M.
Liu: Journal of Materials Science &Engineering, Vol. 21(2003), p. 528-530
Journal of Materials Processing Technology, Vol. 125-126(2002), p.242-247

Lee 3 1, 2 Department of Intelligence and Precision Machines, Korea Institute of Machinery and Materials (KIMM), Daejeon 305-343, Korea 3 MTK Co.
These pollutants can be crucial damage to the camera window and peripheral materials especially in clean room condition.
Koh: Journal of Mechanical Science and Technolog, Vol. 19 (2005), No. 1, pp. 97-105
Kim: International Journal of Precision Engineering and Manufacturing, Vol. 4 (2003), No. 4, pp. 57~63
Wulff: Surface Science, Vol. 454 (2000), pp. 790-795

Besides, the usage of high-grade concrete can improve the crack resistance of concrete bearing material.
Transportation Engineering Journal, 1980,106(5), pp. 493-506
Journal of Transportation Engineering, 2009, 135(11), pp. 813-821
International Journal of Geomechanics, 2001,1(3), pp.291-307
Journal of Transportation Engineering,ASCE,1995,121(3), pp. 289~298

Materials of the study The fabric used in this study is a commercial glass plain weave fabric (Fig. 1.b).
Verpoest, Simulation of multi-layered composites forming, International Journal of Material Forming. 3 (2010) 695–698
Rebouillat, Tribological properties of woven para-aramid fabrics and their constituent yarns, Journal of Materials Science. 33 (1998) 3293–3301
Sherwood, Lu Liu, Julie Chen, Modeling of friction and shear in thermostamping of composites: part I, Journal of Composite Materials. 38 (21) (2004) 1911–1929
Ouagne, Soulat, Influence of the dry woven fabrics meso-structure on fabric/fabric contact behaviour, Journal of Composite Materials, Accepted (2011).