Search results

Materials and Methods Adsorbent was prepared as follows: Fresh cucumber was purchased from the local market and peeled it; the peel was washed with tap water for three times followed by distilled water three times.
Das, Linearised and nonlinearised isotherm models optimization analysis by error functions and statistical means, Journal of Environmental Health Science and Engineering, 12 (2014) 1-6
Journal of dispersion science and technology, 34(10) (2013), 1295-1307
International journal of environmental science and technology, 16(1) (2019), 237-248
Journal of Dispersion Science and Technology, 38(3) (2017), 381-392.

Indentation Size Effect during Measuring the Hardness of Materials by Spherical Indenter Andrey A.
Oliver, Critical issues in making small-depth mechanical property measurements by nanoindentation with continuous stiffness measurement, Journal of Materials Research, 24(3) (2009) 653-666
Konstantinidis, On the interpretation of the indentation size effect (ISE) through gradient theory for Vickers and Berkovich indenters, Journal of the Mechanical Behavior of Materials, 25(5-6) (2017) 161-164
Presnyakov, The center of deformation in the processing of metals by pressure, Science, Alma – Ata, 1988
Diagnostics of materials, 6(81) (2015) 52-56

Piezoelectric material is a kind of important functional materials.
Recently, the electromagnetic-mechanical coupling problems in magnetostrictive materials and structures have attracted considerable attention of engineering and science researchers.
Journal of Chongqing Jianzhu University.
Journal of Taiyuan University of Technology.
Nature Materials.

Optimization of Unidirectional Material Handling System with Short-cut Kun XIA 1, a Juntao LI 2,b and Hiroshi KISE 3,c 1,2College of Engineering Science and Technology, Shanghai Ocean University/Shanghai 3 Kyoto Institute of technology/Kyoto, Japan a cherise_kun@163.com, b jtli@shou.edu.cn, c kise@kit.ac.jp Keywords: Material Handling System; Scheduling; Short-cut; Optimization Abstract: Unidirectional circulation-type material handling system on a single loop with a shortcut is a typical and basic unit in a flexible manufacturing system (FMS).
Processing stage Vehicle Fig.1 Unidirectional Material Handling System with Short-cut.
Journal of Intelligent Manufacturing, Vol.15 (2004), p. 87-102 [2] Nobuaki Ishii and Joseph J.
The International Journal of Flexible Manufacturing Systems, Vol.6 (1994), p. 69-87 [3] Srinivasan Rajagopalan, Sunderesh S.
European Journal of Operational Research, Vol.178 (2007), p. 85-91

A Study on the Optimization of Box-type Kitchen Equipment Materials Xianghong Zhang 1 , Han Yang1, a, Yanjun Li1, Lijun Yin1 1 The Quartermaster Institute of General Logistics Department of the PLA, Beijing ,China a yanghanok@qq.com Keywords: SPSS Software, Box-type, Kitchen Equipment, Materials Abstract.
The research has compared and analyzed the performance parameters of different materials.
Using this approach with high precision and relatively simple principles, we can analyze the materials of the box-type military equipments objectively.
[3] Ying Yang, Chinese Science Forum 2011.07 The Random Variance of Nonlinearity Frame
[8] Xiaoyi LI, Zhaodi XU, Dominant Position and Application of SPSS Software in Probability and Statistics Curriculum Set, Journal of Shenyang Normal University(Natural Science Edition.2010.01 [9] Linquan Zhang，SPSS software in the statistics problems and Countermeasures.

Introduction The research of carbon fiber functional materials at present mainly include carbon fiber reinforced cement-based composites,polymer-matrix composite materials,metal-matrix Composites etc.
Polymer-matrix carbon fiber composite materials include conductive polymer materials,smart layer of carbon fiber felt,carbon fiber multiply laminate and resin continuous fiber and so on.
New Carbon Materials. 2008, 23(2)159~164 [6] M.
Journal of functional materials. 2009,39(3)440~442 [8] Zhang Xiaoyu, Li Zhuoqiu, Song Xianhui.
Sensor function characteristic research of carbon fiber smart layer [J].journal of Huazhong University of Science and Technology , 2008，25（2）：36-38 [9] Shen Lie, Yi Xiaosu.

Analysis of the strain-rate beahavior of a basalt fiber reinforced mortar Domenico ASPRONE 1, Fabio IUCOLANO2, Ezio CADONI3, Andrea PROTA1 1Department of Structural Engineering - University “Federico II” of Naples, Naples, Italy 2Department of Materials and Production Engineering - University of Naples “Federico II”, 3University of Applied Sciences of Southern Switzerland, Lugano, Switzerland Keywords: Basalt fibers, fiber reinforced mortar, tensile strength, strain rate, Dynamic Increase Factor.
Fiber reinforced inorganic materials, such as concrete or mortars, are expected to present good mechanical properties in case of high dynamic loading conditions, as those induced by impact or blast actions.
Introduction Investigation on dynamic properties of construction materials is becoming a crucial issue for structural engineering.
UK. 1993 [2] Malvar L.J. and Ross C.A. ”Review of strain-rate effects for concrete in tension” ACI Materials Journal vol. 95. 1998. pp. 735-739 [3] Banthia.
ACI Materials Journal. vol. 95. 1998. pp. 609-616

Materials and Methods Materials for sleepers were prepared on the basis of the production of wood-polymer composites (WPC) by Savewood.
Materials[J].
Stroitel’nye Materialy [Construction Materials]. 2020.
Journal of Railway Science and Engineering. 2019, 3.
Stroitel’nye Materialy [Construction Materials]. 2018.

The possibility of using materials with nanocrystal structure for structural purposes has emerged with the emergence of technologies for obtaining volume nanostructured materials.
One promising method of improving the mechanical properties of nanostructured materials can be ultrasonic treatment, which allows to treat ultra-hard and brittle materials.
Solovev, Modeling the propagation of elastic ultrasonic waves in isotropic and anisotropic materials when excited by various sources, Materials Science Forum 945 MSF, 945 (2018) 926-931
Solovev, Construction of a generalized fatigue diagram of metallic materials, Materials Science Forum 945 MSF, 945 (2018) 563-568.
Review, Letters on materials. 8 (2018) 372-381

Welded samples were performed in partnership with Graz University of Technology, Institute of Materials Science, Joining and Forming, using the electron beam welding equipment “Chamber Machine EBG 45-150 K14”.
The melt ejection from the copper cylinder is due to an overpressure applied to the melts. 2.3 Welding process and equipment The amorphous ribbons were welded using the equipment of the Institute of Materials Science, Joining and Forming in Graz, Austria: Chamber machine EBG 45-150 K14 produced by German manufacturer Pro Beam.
Awan, Electron beam brazing of Zr62Al13Ni7Cu18 bulk metallic glass with Ti metal. journal homepage: www.elsevier.com/locate/vacuum; [8] Jonghyun Kim, Y.
Electron beam welding of Zr-based BMG/Ni joints: Effect of beam irradiation position on mechanical and microstructural properties, Department of Material Science, Kumamoto University, Kumamoto 860-8555, Japan [9] E.
Laser processing of bulk metallic glass: A review.Journal of Materials Processing Tech. 247 (2017) 73–91; [10] Jonghyun Kim and Y.