Search results

Table 1 gives the hardness, fracture toughness and density values of the boride materials.
Fig. 5 shows the variation in loads for AlMgB14 materials with 0, 30 and 70 wt% TiB2 proportions.
Mechanism of reactive sintering of MgAlB14 by pulse electric current, Journal of Refractory Metals & Hard Materials. 27 (2009) 556-563
Russell, Al2MgO4, Fe3O4, and FeB impurities in AlMgB14, Materials Science and Engineering. 351 (2003) 117-122
Effect of Electric Current on the Performance of Bi1.2Sb4.8Te9 Thermoelectric Material Prepared by a Field-activated and Pressure-assisted Sintering Process, Journal of electronic materials. 40 (2011) 765-768

Rock masses without pre-existing macrocracks can typically be considered materials with only microcracks.
Oparin, Zone disintegration of rocks around underground workings—Part I: Data of in-site observations, Journal of Mining Science. 22 (1986) 157-168
Toupin, Elastic materials with couple stresses, Arch.
Guzev, Thermo-mechanical model of elastic-plastic materials with defect structures, Theoretical and Applied Fracture Mechanics. 33 (2000) 165-171
Guzev, Non-Euclidean models of elastoplastic materials with structure defects, Lambert Academic Publishing, 2010

Also, all materials used where the cavitation occurs, are more or less destroyed by cavitation erosion [1].
Florea, Cavitation erosion behavior of the antifriction alloy YSn83, Materials Science Forum 782 (2014) 257-262
Nedelcu, Gray cast iron behaviour in cavitation erosion, Materials Science Forum 782 (2014) 269-274
Lupinca, Cavitation erosion research on the X3CrNi13-4 stainless steel, Materials Science Forum 782 (2014) 263-268
Florea, Research through the stationary specimen method of the X20Cr13 stainless steel used for hydraulic pumps, Materials Science Forum 782 (2014) 251-256

Simulation of Multifilament Superfine Denier Polyester Melt Spinning Nanfan Li2,a, Chunwang Yi2,b and Chaosheng Wang1,2,c 1State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, Donghua University, Shanghai 201620, P.
China 2College of Material Science and Engineering, Donghua University, Shanghai 201620, P.
[2] T.H.Oh: Journal of Applied Polymer Science Vol.102 (2006), p. 1045-1051 [3] P.T.
Mathur: Journal of Applied Polymer Science Vol.116(2010) , p. 2541-2547 [4] A.D.
Harvey: American Institute of Chemical Engineers Vol.53(2007), p. 78-90 [5] C.Zhang, C.Wang and H.Wang: Journal of Macromolecular Science Vol.46 (2007), p. 793-806 [6] X.H.Yu: Journal of China Textile Vol.15 (1998), p. 9-14 [7] A.

References [1] FRANCIS AO, EDWIN GB, DEATHERAGE JH, ACI Materials Journal, 88(2), 115-121
[5] OLUOKUN FA, ACI Materials Journal, 88 (3), 302-309
[7] RASHID MA, MANSUR MA, PARAMASIVAM P, Journal of Materials in Civil Engineering, 14(3), 230-238
[8] Arıoglu N, Girgin ZC, Arıoglu E, ACI Material Journal, 103(1), 18-24
ACI Materials Journal, 87(1), 47-53

All materials are used without further modification.
Rhee: Journal of Macromolecular Science, Part B, 48, 3 (2009), p.626-634
Thomas: Journal of Polymer Science, Part B: Polymer Physics, 40, 8 (2002), p.755-764
Cho: Dental Materials, 21, 4 (2005), p.354-364
Mower: Materials Science and Engineering: A, 176, 1 (1994), p.79-90.

Materials and methods Materials.
SiO2 was the main inorganic materials in biological embedding process[18], because of its non-toxic and thermodynamics stability.
The IM balls had improved by adding support materials SiO2, CaCO3 etc.
Apertures of outside surface after adding support materials(Fig. 4-B)were close to that of inside, but were bigger than no support material.
Su: Journal of Materials Chemistry. 18 (2008), p. 1333- 1341

Takacs, Materials Science Forum 225-227, 553 (1996)
Takacs, Progress in Materials Science 47, 355 (2002)
Cocco, Materials Science Forum 225-227, 237 (1996)
Journal of Materials Processing Technology 138, 394 (2003)
McCormick, Materials Science Forum 88-90, 779 (1992)

Introduction Resin Transfer Molding (RTM) is one of the most used manufacturing processes for industrial composite materials [13].
Composites Science and Technology, 71,1623–1631, (2011)
International Journal of Material forming, 3(Suppl 2): 1205-1216, (2010) [13] Rudd CD and Long AC (1997).
Computational Materials Science. 40:439–448 [15].Arbter et al (2011).
Journal of Composite Materials, 44(1), 2010, 5-22

The effect of percentage of primary α on mechanical properties of bimodal microstructure of TC4 Jingmin Yang1, a, Yangwei Wang2, b, Jubin Gao3, c, Pan Xiong4 1,2,3,4School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081, P.R.
China1; National Key Laboratory of Science and Technology on Materials under Shock and Impact, Beijing 100081, P.R.
Effect of primary α phase volume fraction on tensile property and thermal stability of near-alpha TG6 titanium alloy: Journal of Aeronautical Materials, Vol. 27(2007), P. 17-22
Low-Cycle Dwell-Time Fatigue in Ti-6242: Metallurgical and Materials Transactions A, Vol. 30(1999), P. 2383-2389
Physical processes and regimes of thermomechanical processing controlling development of regulated structure in the α + β titanium alloys: Materials Science and Engineering A, Vol. 243(1998), P. 77-81.